MiniSimp's 1985

[*** YELLER ***]

Well then why dont we just cut the ends off this one   add a hitch reciever and call it good

[MiniSimp]

looks like the mounts are too wide.

[*** YELLER ***]

Then we will narrow them and make it work 

[MiniSimp]

Negative!

Get your ass over to Franks and pick up that 1983 pickup would ya!

Slacker.

[*** YELLER ***]

The seat is in, and not just sittin there its realy bolted to the floor

As far as the 83 you suck !!!! not only will I have to build the trailer but then hope the 83 dont fall off on the trip home. WE need to do that after WE build the trailer than I bought for your YODA, ol' buddy, remember  oldyeller can drive faster than 35 mph down the road   it doesnt require a trailer to go from here to there..   I dont know, I just felt like calling you an idiot.

[MiniSimp]

Dave, change of plans for the bumper, cut on the red lines. I'll be relocating the turnsignal mounts to the inside.

[DTB]

that doesn't seem to offer much corner or even front protection to me. It would be more like a bull/push bar.

[MiniSimp]

I doubt we will be able to get it but if we do it will only be for bumping into trees and rocks pretty much like a bull bar it is mainly for radiator protection.  If we don't get it we'll end up putting on my old chromie 

p.s. dave, Cristie says "Hi Princess" 

[*** YELLER ***]

Yea thats, JUST WRONG Cristie.

I'm gonna try to get ahold of John and see about that bumper.




P.S. Cristie

[*** YELLER ***]

OK  :disturbed:got the trailor to the house now just need to build it up so it can haul your YODA 

[MiniSimp]

I got some more done today:
Mounted Super Mud Flaps
Installed speedo extension
Lengthened 4WD indicator light wire
Built Licence plate frame

Ready to wheel!

[MiniSimp]

Just updating the specs

1985 & 1987 Frankenstein 22RE
1983 Front Axle
1986 Power Steering Box
106" Wheelbase
2.28 Crawler Box with stock shifter
2.28 Rear Transfer Case
48" High-Lift Jack With Mounts
Aussie Locked 4.10:1 Front
Black Rock Krawler Wheels 15x10"
Bucket Seats (stock)
Chevy Rear Springs (3 leaf + overload cut down)
Front Range Offroad Steering Frame Brace
Front Range Offroad Transfercase Center Section
Front Range Offroad Twinstick Shifter
Home Built Chevy Spring Hangers
Home Built Flat Bed
Home Built Gas Filler Hose Mount
Home Built Mud Flaps
Home Built Rear Pivoting Spring Perches
Home Built Rock Sliders
Home Built Shift Knobs
Home Built Video Camera Mount
Interco Tire Superswamper Boggers 35x14.50x15R
Interior Roll Cage
Johnny Joint Rear Shackles
Magellan Meridian Color GPS WAAS Compatibility
Marlin Crawler 1.5" Wheel Spacers (Front)
Marlin Crawler 26" Brake Line 3 piece kit
Marlin Crawler Drag Link
Marlin Crawler Low Profile Drain Plugs
Marlin Crawler MC08-R10 Clocked Adapter
Marlin Crawler Rebuilt Knuckles
Marlin Crawler Speedometer Extension
Marlin Crawler Steering Arms
Marlin Crawler Tie Rod
Marlin Crawler Transfer Case Rebuilt
Marlin Crawler Tube Doors
Marlin Crawler U-Bolt Flip Kit (Front)
OTT Industries Flat Pitman Arm
Paint - Hammered Black Spray Can
Procomp ES1000 14" Travel Shocks (rears mounted at 50 degrees [64% effective])
Procomp ES2000 Steering Stabilizer
Sliding Tinted Rear Window with ghey purple tint
Thales Navigation Swivel GPS Mount
Toyota 1985 Rear Springs Up Front (4 Leaf)
Trail Gear 2" Wheel Spacers (Rear) (and free)
Unleaded Gas
W56 5 Speed Manual
Weatherguard Tool Box
Welded 4cyl 4.10:1 Rear

[MiniSimp]

Just ordered up some new Bling from OTT Industries!

[Ramrod]

why mudflaps if you dont drive it on the street?

[MiniSimp]

Until I get a tow rig, it will be driven on the street to local trails.

[whiteman]

Just ordered up some new Bling from OTT Industries!

Ohh!  I wish I could have got a shiny one, it would look good sitting in front of JC-Penny next to a fat Mercedes

[Wermz84]

Black Rock Krawler Wheels 15x10"

Interco Tire Superswamper Boggers 35x14.50x15R

Marlin Crawler 1.5" Wheel Spacers (Front)

Just wondering, what kind of backspacing are you running on those wheels, and do you get any rubbing with that setup?  Up front since you have no bed.

thanks

[MiniSimp]

Just wondering, what kind of backspacing are you running on those wheels, and do you get any rubbing with that setup?  Up front since you have no bed.

thanks

The front does not rub at all.
The rear (which out flexes the front now) rubs on the top of the frame.
The wheels are 15x10" 3.25" BS with 2" spacers in the rear and 1.5" spacers in the front.

[Wermz84]

The front does not rub at all.
The rear (which out flexes the front now) rubs on the top of the frame.
The wheels are 15x10" 3.25" BS with 2" spacers in the rear and 1.5" spacers in the front.

Cool, thanks. 

[MiniSimp]

Sweet!  Just a little beefy!!!!

[Rocksurfer]

Ohhhh, so perdy....

[*** YELLER ***]

SWEEEEEET        


                                   MINI
                                 


                       THE REST OF US....

[Wermz84]

[Cartman_voice] Beefcake!! [/Cartman_voice]





I can't wait to see your rig on the trail.. 

[MiniSimp]

Got some really bad cell phone pics on the ramp today.
Going wheeling tomorrow.

[6.72:1]

Hmmm...can't wait to see the wheelin' pics!

[toybuilt]

Looks pretty good, wish mine was drivable again.

[DTB]

  Lookin' really sexy now

[*** YELLER ***]

Wheelin went good, nothing broke, lots of smoke from an oil leak though.

[*** YELLER ***]

Couple pics from wheelin'

[MiniSimp]

Yeah, it figures, the guy who takes tons of pictures forgets his camera!
Thanks for the pics Dave.