Author Topic: Zebra 85 2wd to 4wd( The Sketchy Build!) (Read 82282 times)

zebracrawler · « **Reply #150 on:** Oct 24, 2011, 07:22:52 PM »

haha looks good out of the garage dumb it broke i think it might be that crawl box input that broke

91 ex-cab · « **Reply #151 on:** Oct 24, 2011, 07:37:17 PM »

4x4yota · « **Reply #152 on:** Oct 24, 2011, 07:39:11 PM »

very cool... looks great!

Zs Confederate Toy · « **Reply #153 on:** Oct 24, 2011, 07:42:40 PM »

Definitly looks good out of the garage. Great work guys

zebracrawler · « **Reply #154 on:** Oct 24, 2011, 08:30:51 PM »

looks good doesn't drive so good ha-ha need to get it fixed hope its just a input shaft into the transmission

Zs Confederate Toy · « **Reply #155 on:** Oct 24, 2011, 08:33:54 PM »

Quote from: zebracrawler on Oct 24, 2011, 08:30:51 PM

looks good doesn't drive so good ha-ha need to get it fixed hope its just a input shaft into the transmission

Unmatched splines or what?

zebracrawler · « **Reply #156 on:** Oct 24, 2011, 08:44:24 PM »

don't know yet i have to pull the cases out

zebracrawler · « **Reply #157 on:** Oct 24, 2011, 08:49:41 PM »

im getting a wine sound from the transmission pulled the block off plate off my crawl box and no gears were moving when i put it in any gear but when you change gear the wine sound changes so i know my gears are spinning in the transmission. so ether there is something broken in the transmission or its the input.

Zs Confederate Toy · « **Reply #158 on:** Oct 24, 2011, 09:35:56 PM »

Well that doesnt sound fun at all. Especially after just putting it up in there

zebracrawler · « **Reply #159 on:** Oct 24, 2011, 09:40:38 PM »

yeah drove it like 200 feet then broke i was kinda mad about that but it did drive

Zs Confederate Toy · « **Reply #160 on:** Oct 24, 2011, 09:57:30 PM »

At least it drove. You know it worked, even if it was only for a minute lol

4x4yota · « **Reply #161 on:** Oct 25, 2011, 11:57:32 AM »

Hopefully you get it all sorted out so you can ho and play... I know the feeling of not being able to drive your truck for a while and bo being able too... Im sure Z does too lol

Zs Confederate Toy · « **Reply #162 on:** Oct 25, 2011, 01:22:04 PM »

Quote from: 4x4yota on Oct 25, 2011, 11:57:32 AM

Hopefully you get it all sorted out so you can ho and play... I know the feeling of not being able to drive your truck for a while and bo being able too... Im sure Z does too lol

Oh I do all too well haha

zebracrawler · « **Reply #163 on:** Oct 25, 2011, 01:35:02 PM »

yeah i just want to know why it broke and if it will do it again if i fix it

Zs Confederate Toy · « **Reply #164 on:** Oct 25, 2011, 01:50:16 PM »

I would think its bound up somewhere

zebracrawler · « **Reply #165 on:** Oct 25, 2011, 02:09:31 PM »

yeah i think so too

91 ex-cab · « **Reply #166 on:** Oct 25, 2011, 02:18:58 PM »

If its input its either bound or we stressed it when we put it in. It felt like it spun just fine though, so I'm thinking tranny is still a possibility. Only one way to find out

zebracrawler · « **Reply #167 on:** Oct 25, 2011, 03:26:41 PM »

yeah im hoping its the output

89sastoyo · « **Reply #168 on:** Oct 25, 2011, 05:53:55 PM »

so i kinda read but not completly im a little intoxicated, but if your tranny makes noises through the gears but your t case is not spinning than you broke an input. This is what i do when i break my t cases. immediatly yard on the rear d-line because it will move a lot if its an output or fall and hit you in the face. If the driveline is not lose or has a lot of play it could still be the output so i pull my front and rear case shifters off plate n all and then go through the gears usually like how mine are right now the front case will spin and the rear wont so right now i either broke yet another 4.7 input or i finally took out the dual case collar that adapts the front to the rear because a few buddies have been breaking those. with that said if you havent pulled the shifters and looked which i believe i read previously than i would. and if nothing is spinning you deff broke an input or forgot a c' clip and now have a gear wehre its not supposed to be so nothing engages. boom the end ya

zebracrawler · « **Reply #169 on:** Oct 25, 2011, 06:24:56 PM »

yep i got a forward shift t case so i pulled my block off plate on top of my crawl box and looked down it wile the truck was running and ran it through all the gears and nothing was spinning so i'm pretty sure i broke an input. my drive line didnt fall on my face because i checked that after i pulled it back up the hill and it was good.

89sastoyo · « **Reply #170 on:** Oct 25, 2011, 06:42:54 PM »

yeah deff an input if you have a single case or somehting is bound did you make sure your shifter is in gear while the shifter was out that could happen as well

91 ex-cab · « **Reply #171 on:** Oct 25, 2011, 07:17:57 PM »

Input was the first thing I said when it happened. But the fact that it hooked up and moved for a second after it broke makes me wonder.

zebracrawler · « **Reply #172 on:** Oct 25, 2011, 08:36:55 PM »

yeah but i t wasn't like it really hooked up it just grinded in gear for a sec there could have been a bur on the broken spot or something or it was on that hill and just made me think it went in to gear

zebracrawler · « **Reply #173 on:** Oct 27, 2011, 08:51:09 PM »

well i'm starting to build a square shaft and a sweet bracket to pull my dual cases without lifting them above my head

zebracrawler · « **Reply #174 on:** Oct 27, 2011, 08:55:21 PM »

used a lath to cut off the joints worked very good i cut out some frame plates for the truck on the cnc plasma because they do not have a plate for a 2wd frame designed them in cad turn out good will put some of the finish product soon you can see one in the bottom of the picture