1966 Toyota Stout Build (20/22R Hybrid)

[Zs Confederate Toy]

Looks good

[SloCrawler]

Right now my truck is 22.25" to frame, all thats left to do is 54" driveshaft and shocks s far as suspension goes

[SloCrawler]

this should work, I see lots on pirate doing it

[SloCrawler]

so got drivelines done, a buddy had a longer slip yoke which exteded my rear 1.5" more, then i flexed her out on the lift. i got 5" of up travel all around, and on the lift i would be useing almost the length of my 14" bilsteins at droop. My rear tire got 42" up befor the other started to lift. now I just have to mount them damn shocks.

[Zs Confederate Toy]

Schveet!

[bigarms23]

good job

[SloCrawler]

Got shocks mocked up, looks like the f250 mounts have to be welded on top of the frame to achieve the amount of uptravel I want. Hopefully I get a good welder up in here soon I want to do a shake down allready.

[jackson58]

Looking good but it looks like you may need to make more room for the tire.

[SloCrawler]

not tell 37"

[SloCrawler]

My buddy Brian came over and burnt some steel for me. Rear shocks all done going attempt the fronts today, here is is 4runner all doved front and rear

[superyota]

My buddy Brian came over and burnt some steel for me. Rear shocks all done going attempt the fronts today, here is is 4runner all doved front and rear

alfonso?

[toyotathomas]

Holy stinger!

[SloCrawler]

I forget his last name, all tattood up, hes part of wrecked 4x4

[SloCrawler]

rear and front shocks all done, maybe add a few more gussets

[superyota]

looks good chris.  so you ready for the roundup?  are you planning on meeting up with and caravaning up or just meeting us there?

[SloCrawler]

where you meeting up for caravan. Need to do clutch, timing, adjust valves, and assist and im ready

[superyota]

we are all meeting up in bakersfield, just because thats where almost everyone that is in our group is from.  but we can meet up anywhere off the 99 or even in sac if you don't want to drive to bakersfield.  up to you.

[SloCrawler]

sac would be less driving for me. When you think youll be around their?

[superyota]

leaving bako around 8am or so. should be in sac around 1pm

[SloCrawler]

Friday right?

[superyota]

thursday. 

[SloCrawler]

front shock pics. Think i need to gusset the sides of the f250 mounts? I got the fronts and planning on doing backs, and should i put spacers in between shocks or just run em?

[jrock]

Id add some gussets and a couple washers. Also add some steel to that cutout And bend the brake line a little.

[SloCrawler]

After talking to a few peeps im going to just pull a stud on steering knuckles and drain oil, and pack full of grease without pulling apart the knuckles, seeing how this truck is a trailor queen I shouldnt have any problems. Im going to Coast Clutch and Brake today to get a few lines made for my after market resevor, then i should have everything to finish my hydro assist. Oh and MC said my 1600lb clutch should be here today. 3 weeks left and my list of things is getting much smaller

[Peterbuilt84]

Truck's coming along nice   You could also use the camo method for taking off your knuckles, should be able to pack them and clean them out better that way.

[SloCrawler]

Truck's coming along nice   You could also use the camo method for taking off your knuckles, should be able to pack them and clean them out better that way.

i searched and didnt find anything.. Whats Camo method?

[Peterbuilt84]

Here's a vid http://www.youtube.com/watch?v=o3Y5bQGiezY

[SloCrawler]

thanks, looks alot easier that way

[Peterbuilt84]

Glad to help  I've read about how to do it, but the video makes it look pretty simple.

[SloCrawler]

got everthing now to finish assist