anything you have FABBED

[89trailrunner]

How about dropped framerails to accomodate the stock tailgate on a 14.5" bobbed 4runner?


build thread: http://www.pirate4x4.com/forum/showthread.php?t=720038

[ROKTOY829]

Front driveshaft I made.

[Toymin8r]

Custom motor mounts for a v8 swap - still not finished yet in the pic.  


2000 Sport Edition hood scoop on my 89 hood -    uhhh....still not done yet.


Bed Bob - Destroyed it already

[joey0712]

Some driveline hoops i made on the mini monster truck.

[*ROKTOY*]

1/8" galvanized sign post.....

this baby aint never gonna rust off again...



Holly erector set, WTF is that?

[hilux-1983]

Hey Mnmstoy, I think you aughta make your own build thread. I'm pretty impressed with the body work. I've thought about joining the two cabs to make it a 4door. Have you seen any done like that? Since we can't get them from over seas, I'll have to fab it myself.

[82juguete]

Here you go hilux:

http://board.marlincrawler.com/index.php?topic=12165.0;highlight=extend+a+toy

And heres the easier route Im planning to take someday:

http://board.marlincrawler.com/index.php?topic=55111.0;highlight=1st+gen

[Yota Rolla]

1/8" galvanized sign post.....

this baby aint never gonna rust off again...

damn i hate rust. . can you make me a full frame?!?! 

[4runner freak]

I designed and milled a custom set of steering arms.




I also designed a dual tranny adapter and had it machined.

[Sparkplug]

made this custom pitman arm, 2wd sector shaft piece, attached to 4wd rod end piece, angled and lengthened to exactly wat i needed

[joeycool00]

front bumper and fairlead fender sliders rear tire and jack holder

[Slolyfe]

Well I drank a 5th of Crown tonight and started screwing around. Here it is, old fire extinguisher to on board air tank. Just need to buy a female air attachment. But it holds air.

[locked 4x4]

1

[locked 4x4]

1/8" galvanized sign post.....

this baby aint never gonna rust off again...

LOL  wrong thread,  This belongs in the disgrace to off road.

[Jud]

Well I drank a 5th of Crown tonight and started screwing around. Here it is, old fire extinguisher to on board air tank. Just need to buy a female air attachment. But it holds air.

Damn firefighters...

[Slolyfe]

Damn firefighters...

Hahaha you gotta use what you have laying around. It works great!

[joeycool00]

Hahaha you gotta use what you have laying around. It works great!

hehe I did that to an scba LOL

[4LoRunner]

slolyfe what the max psi on that tank u made? and same goes to joey.

[4runner freak]

I had the same system.
Old school Aluminum Fire Extinguisher that a buddy(worked in Fire safety) gave me. He tested it to 1800psi(IIRC).

[joeycool00]

slolyfe what the max psi on that tank u made? and same goes to joey.

1800 psi but I'm going to keep it at 150 with my on board comp...

[Slolyfe]

slolyfe what the max psi on that tank u made? and same goes to joey.

I don't know. Extinguishers are rated to higher than 150 psi. The exact amount im not sure. But my compress or only goes to 140.

[yota4x4sc]

my truck and my bros samurai we made

[motormouth559]

1989 Mazda B2600 Xcab it had Mazda Dot Toyota parts First SAS

[motormouth559]

lol man lots of drinking with that build !!!!

[bleakhorizon]

it aint as hardcore as some this stuff...

but dual case cross-member

[86bobbedtoy]

hay thats sweet.
bet you saved a few hundo there.
it does the trick right.
Id run it

[bleakhorizon]

oh.... yea guess i did make a square drive shaft..... used it one run and its now a paperweight....

[Steve_925]

had to make a cart for the new welder and plasma cutter

[4RunnerChevy]

Oh crap, I cant keep up

http://board.marlincrawler.com/index.php?topic=55343.new#new

[Goldrush]

I also designed a dual tranny adapter and had it machined.


[/quote] why would you do a dual tranny setup? is it actually in your truck? and how does that work?