***CODY'S RUNNER*** *REDEMPTION**

[brockbuilt85]

Sounds like the battery is low or the timing is too far advanced. 

i have not messed with the timing yet. but your the second person to mention it. ill mess with it next chance i get tho and see what happens. the battery is new, and i had a jump box hooked up to it.

[fordh8r]

Good place to start. 

[brockbuilt85]

Good place to start. 

would it not even pop if the timing was off? i mean, its turning over, but not even tryin to start, i got fuel(pretty sure) and spark(definatly)

[fordh8r]

It could, but if it's advanced enough to still contain the fire during the compression stroke, it with just resist the upstroke as you crank causing it to crank rather slowly and somewhat erratic as it sounds in that video.  

[brockbuilt85]

It could, but if it's advanced enough to still contain the fire during the compression stroke, it with just resist the upstroke as you crank causing it to crank rather slowly and somewhat erratic as it sounds in that video. 

good to know. i might be motivated enough to work on it again tomorrow

[fordh8r]

Keep us posted on what you find. 

[*** YELLER ***]

Keep us posted on what you find. 

tryed timing but still sounds the same 

[*** YELLER ***]

http://www.youtube.com/watch?v=ROveXuKOb54




Wtf...

[fordh8r]

Sounds like it's cranking faster. What about fuel? Try using a qick spritz of carb cleaner into the throttle body and see what happens. 


Carlos asked if you got the rag outa the intake? 

[*** YELLER ***]

Carlos asked if you got the rag outa the intake? 

Like I need to... 



http://www.youtube.com/watch?v=QhdIWy6CFdE

[brockbuilt85]

who is that goofy retard?

[brockbuilt85]

thanks 86turboypta and minisimp for your input today! without you it would still be a pile of poo, now its a running pile of poo. and the passenger window now seems to work, sweet.
need to:
adjust valves
fill radiator up all the way
get power steering lines working right
put hood on
change windshield
install cases (thanks duffil)
get d-lines
check brakes
clean out
install passenger seat
cage
sliders
bumpers
register
stereo/CB

[fordh8r]

So what was wrong? 

[Duffil]

so much for the water wagon.

thanks dave.

[brockbuilt85]

So what was wrong? 

bad ground and basically a vacuum leak. all is well now

[brockbuilt85]

so much for the water wagon.

thanks dave.

hey, thank you. when ever your in my neck of the woods, ill buy you a beer

[fordh8r]

bad ground and basically a vacuum leak. all is well now

At least it was simple. 

[brockbuilt85]

At least it was simple.  

oh yea, we knew it was. we just didnt think we would figure it out.

cause we are ninjas, we did

[subbrat]

So you have any ideas for your front and rear bumpers. Bender is all tuned up. I'm starting to collect pipe and hinges for my tube doors.

[brockbuilt85]

So you have any ideas for your front and rear bumpers. Bender is all tuned up. I'm starting to collect pipe and hinges for my tube doors.

no clue, i have that one thing for the front, as for the back im more concentrated on getting the cases in and getting it running well.

update: passenger window now works fine, thanks carlos!

[brockbuilt85]

insert twin sticks right about here:


update, got the motor running a lil better, and the check engine light wen away, but it seems to be smoking alot from the exahust side (see video) im thinking its burning crap off, plus i still need to adjust the valves, gonna wait till it gets a lil less smokey outside, got a head ache just from being out there as little as i was.
http://www.youtube.com/watch?v=m9Iw3GFdsWM

HEY SUBRAT! think you could take a trip up here and give this pig the once over one more time, just to make sure im still go for launch? ill take you and amy out to the peppery

[subbrat]

The next two week ends are full I have to go get the willys and re smog the camaro for the trade. After that looks good.

[unclejpl4x4]

i think you should use the hole for a inboard

[brockbuilt85]

The next two week ends are full I have to go get the willys and re smog the camaro for the trade. After that looks good.

oh sweet you found one!
ok, well, let me know when you wanna come up, ill keep workin on it, this weekend the weatehr is supposed to be cooler so ill prolly get a bit done.

i think you should use the hole for a inboard

geesh

[brockbuilt85]

cases almost in, had a coolant problem, didnt hook up ne of the hoses, adjusted the valves today too. still runs a lil rough. just taking a break before i fnish the case mounting.

[brockbuilt85]

cant get the cases in by myself, gonna get some help tomorrow. and then once i get them in, shifter and cross member. im gonna need some drivelines. soon.

[brockbuilt85]

DUAL CASES IN!!
pics up asap!

[brockbuilt85]

sorry for the cell phon pics, its all i had at the time, dave took all his cameras and i forgot mine

[Tallchevy]

Looking good 

[brockbuilt85]

took my drivelines to Marty Built today. also got drain plugs, and bolts for the shifters, oil for the trans/transfercases. still runs a lil rough, but i need to put some plugs in it, see what that does, and put the real exhaust i have on it. wish i knew how to weld worth a so i could get some of that started, i feel like im behind the 8 ball as far as the roundup goes. geesh!