Project "RAWHIDE" a High School buildup !!!shackles installed no pics.....yet!!

[Rainer]

http://cgi.ebay.com/ebaymotors/Toyota-Pickup-Truck-4Runner-22RE-INJECTOR-PLUGS-1987_W0QQitemZ320127850981QQcmdZViewItem?hash=item320127850981

if the truck as been sitting for a bit and not ran you should be able to pull the fuel rail and injectors with out fuel spraying all over. That look like antifreeze or the green mud u sucked up  .

What could it be?

[Rainer]

I pulled my injectors tonite. THey came out very easy, is that normal. Two are green on the end and two are black? The green ones have what looks like mesh in the top, and the black ones are just black and i cant see anything, could they be clogged? Also were would my fuel filter be, i folled my lines coming pout the back and follwoed them all the way to the gas tank, no fuel filter? I need HELP and Fast!!!!!!

here are some pics

[Cheesemaker]

I'm not sure about the injectors, maybe they have been switched out one time?  As for the fuel filter, it should be directly below your intake runners, above the starter, and to the left of your oil filter.  It is one of those feel and do by hand jobs.  You'll need a 12mm socket to unbolt the filter,  and a 17mm wrench for the banjo fittings!  Here is a picture of where it's at.  Look for the shiny black canister to the left of the oil filter!


What line you followed was probably the return line!  Hope this helps!

[Rainer]

I fixed the truck. I bought some injectors off of ebay from a guy in hawaii. The came from an 87 22re. I installed them with new gaskets straight from toyota, expensive!!!! It run snow with no problems. Im so happy and i did it myself. IM only 17. I just purchased elocker harnesses and 6 inch shackles from Marlin. I havnt installed either though. FOr the harnesses do i need that upper kit from inch worm? I was looking at the top part of the harnesses and they have a six prong conecter. I dont know how to custom build off of that. Im going to truck fest today as well. Josh we need to install my sliders, i think i need to cut the mounting arms that go to the frame though, they seem to long. I got the gusset kit from those who should not be named.

Mark

p.s. sorry no pics have been busy with work and trying to figure out whats wrong so i had no time to take pics. Plus i have been spending lots of time with my girl friend. She is awesome.

[AaronB]

p.s. sorry no pics have been busy with work and trying to figure out whats wrong so i had no time to take pics. Plus i have been spending lots of time with my girl friend. She is awesome.

Dump the girl and get busy 





Just kidding

[Duffil]

keep the girl and get busy 
then fix the truck




Just kidding

fixed

[Rainer]

LOL, I just got my shackles and elocker harnesses. Cant install the harnesses though, thay have a six prong conector on one side, how would i do a custom harness off of that? Also i fixed the missw fore, but now i get a check enine light every on ce and and a while? What could it be. When it happens it kinda bogs down and then it does have that throttle response. I can tell right before i get the check engine light thats how noticable it is. I need help, i cant even drive it till i figure it out.

Mark

[Rainer]

Shackles are now installed on 3 points. I didnt have enough for the last one, plus i need to remove the bolts on the rear and move them to the front, i screwed up a little lol. THe truck fell tody as well, it fell onto my 3 ton jack and bent it, haha. Luckily it fell slow so we all moved out of the way. I will get pics up tomarrow. Looks good got about 1.50 inches of more lift with the six inch shackles. I now have about a foot between the 33s and the top of my fender. Soon 35s. It looks good too.

Mark

[DTB]

THe truck fell tody as well, it fell onto my 3 ton jack and bent it, haha. Luckily it fell slow so we all moved out of the way.

Mark

how did that happen?

[Jordan7118]

Please document the elocker controls, as I'm soon to do that. Lookin' good thus far, and you found friggin' gold with your elocker front and rear...   

[Vic stuff]

Hey Mark, I saw you today up at go honda lol, I was flying by on federal going south in my chevy.  looks like you got her running alright i assume?

[Rainer]

Hey vic. Yeah she is running very good now. I will be working all weekend and i think i am going to drive her some more. (I assume it was on sunday, bc i am parked out front on sundays. So if i work this sunday you can stop by for a few to check her out. I started school yesterday too.

Mark

[Vic stuff]

would if i was going to be in town, leavin for a hunting trip in the morning tomorrow so maybe another time

[baconator]

i just read your whole thread.  keep up the good work. 

heres a good write up i found on the elocker wiring and stuff back when i was going to run them
http://67.122.16.97/carterman/4runner/mods/locker/#ELECT_MECH

why not run the cable conversion on your elockers?  just curious