MiniSimp's 1985

Started by MiniSimp, January 30, 2005, 10:54:12 PM

0 Members and 4 Guests are viewing this topic.

Print
Go Down Pages 1 ... 85 86 87 88 89 90 91 92 93 94 95
User actions

jrock

#2790
August 22, 2011, 11:15:39 AM
I didnt realize you had a square rear drive shaft :eek: No wonder you never get out and wheel. That thing shakes your teeth out :)


Page 94!   :yikes:

MiniSimp

#2791
August 22, 2011, 11:24:03 AM
Quote from: jrock on August 22, 2011, 11:15:39 AM
I didnt realize you had a square rear drive shaft :eek: No wonder you never get out and wheel. That thing shakes your teeth out :)
Negative. It's balanced up to at least 70mph. Haven't driven faster than that yet. :gap:

jrock

#2792
August 22, 2011, 06:44:06 PM
Crazy :gap:

MiniSimp

#2793
August 24, 2011, 08:56:30 AM
Front end is back on the ground.

To Do List:
Torque lug nuts (80ftlbs)
Torque front 3rd member nuts (19ftlbs)
Install front driveshaft and torque (54ftlbs)
Torque rear 3rd member nuts (19ftlbs)
Inspect rear 3rd pinion seal
Torque transfer case bolts (29ftlbs)
Modify e-brake arms and install e-brake
Clean/paint/install skid plate
Install LED brake lights
Change Oil
Clean engine bay
Clean interior/exterior
Load tools
Load camping gear
Load food
Load truck on trailer and center

all I can think of for now.

unclejpl4x4

#2794
August 24, 2011, 07:02:51 PM
poo box
build thread http://board.marlincrawler.com/index.php?topic=39214.0
CB install http://board.marlincrawler.com/index.php?topic=45467.0
roundeyes http://board.marlincrawler.com/index.php?topic=33294.0;highlight=round+eyes
LC exhaust head 2 tip, EB RVstreethead O/S valves,EB  268c/torker cam , .20 over , metal t-chain wear pads
MARLIN clutch 1200, master clutch cly

MiniSimp

#2795
August 24, 2011, 08:15:39 PM
Quote from: MiniSimp on August 24, 2011, 08:56:30 AM
Front end is back on the ground.

To Do List:
Torque lug nuts (80ftlbs)
Torque front 3rd member nuts (19ftlbs)
Install front driveshaft and torque (54ftlbs)
Torque rear 3rd member nuts (19ftlbs)
Inspect rear 3rd pinion seal
Torque transfer case bolts (29ftlbs)
Modify e-brake arms and install e-brake
Clean/paint/install skid plate
Install LED brake lights
Change Oil
Clean engine bay
Clean interior/exterior
Load tools
Load camping gear
Load food
Load truck on trailer and center

all I can think of for now.

MiniSimp

#2796
August 28, 2011, 07:34:23 PM
Quote from: MiniSimp on August 24, 2011, 08:56:30 AM
Front end is back on the ground.

To Do List:
Torque lug nuts (80ftlbs)
Torque front 3rd member nuts (19ftlbs)
Install front driveshaft and torque (54ftlbs)
Torque rear 3rd member nuts (19ftlbs)
Inspect rear 3rd pinion seal
Torque transfer case bolts (29ftlbs)
Modify e-brake arms and install e-brake
Clean/paint/install skid plate
Install LED brake lights
Change Oil
Clean engine bay
Clean interior/exterior
Load tools
Load camping gear
Load food
Load truck on trailer and center

all I can think of for now.

MiniSimp

#2797
August 31, 2011, 06:33:36 AM
To Do List:
Torque lug nuts (80ftlbs)
Torque front 3rd member nuts (19ftlbs)
Install front driveshaft and torque (54ftlbs)
Torque rear 3rd member nuts (19ftlbs)
Inspect rear 3rd pinion seal
Torque transfer case bolts (29ftlbs)
Modify e-brake arms and install e-brake
Clean/paint/install skid plate
Install LED brake lights

Change Oil
Clean engine bay
Clean interior/exterior
Load tools
Load camping gear
Load food
Load truck on trailer and center

Almost there...

Wermz84

#2798
August 31, 2011, 08:42:21 AM
Nice progress!  I need to get some of your motivation to work on my rig. 
I like to Drive!

jrock

#2799
August 31, 2011, 09:04:16 AM
Two weeks Wermz ;)

Wermz84

#2800
August 31, 2011, 09:04:36 AM
I like to Drive!

MiniSimp

#2801
September 05, 2011, 01:56:53 PM
To Do List:
Torque lug nuts (80ftlbs)
Torque front 3rd member nuts (19ftlbs)
Install front driveshaft and torque (54ftlbs)
Torque rear 3rd member nuts (19ftlbs)
Inspect rear 3rd pinion seal
Torque transfer case bolts (29ftlbs)
Modify e-brake arms and install e-brake
Clean/paint/install skid plate
Install LED brake lights
Change Oil

Clean engine bay
Clean interior/exterior
Load tools
Load camping gear
Load food
Load truck on trailer and center

Almost there...

Shamb

#2802
September 05, 2011, 02:36:45 PM
why in the world would you need to clean the engine bay?  are you going to a show n shine or MCR?!    :talkingn:

;)
R.I.P to my Papa, I miss you pops......

Knowledge is power  www.pirate4x4.com/forum

New Buildup in process 85' 4runner "Bad Decisions"
http://board.marlincrawler.com/index.php?topic=52566.0

Check out my 1-ton build up thread
http://board.marlincrawler.com/index.php?topic=22600.0

brockbuilt85

#2803
September 05, 2011, 08:41:19 PM
getting close!
When in doubt, skinny pedal!
Turd Box Build:
http://board.marlincrawler.com/index.php?topic=50894.0

MiniSimp

#2804
September 06, 2011, 09:24:15 AM
Quote from: Shamb on September 05, 2011, 02:36:45 PM
why in the world would you need to clean the engine bay?  are you going to a show n shine or MCR?!    :talkingn:

;)
It's on the list as something to do, but I don't think it will get done before this trip.

Shamb

#2805
September 09, 2011, 08:30:29 AM
 :biggthumpup:

I've got plenty for you to do, just c'mon by. 
R.I.P to my Papa, I miss you pops......

Knowledge is power  www.pirate4x4.com/forum

New Buildup in process 85' 4runner "Bad Decisions"
http://board.marlincrawler.com/index.php?topic=52566.0

Check out my 1-ton build up thread
http://board.marlincrawler.com/index.php?topic=22600.0

MiniSimp

#2806
September 18, 2011, 10:03:32 PM Last Edit: September 18, 2011, 10:52:33 PM by MiniSimp

fordh8r

#2807
September 18, 2011, 10:55:57 PM
Nice shot! Kinda shows the Steepage!  :biggthumpup:
Quote from: MiniSimp on September 18, 2011, 10:03:32 PM

*** YELLER ***

#2808
September 18, 2011, 11:01:06 PM
and the drippage :rofl2:
MY ONLY REGRET IS THAT I HAVE NOTHING USEFUL TO OFFER THIS FORUM  :moon:
except BACON

fordh8r

#2809
September 18, 2011, 11:02:12 PM
Quote from: ** YELLER ** on September 18, 2011, 11:01:06 PM
and the drippage :rofl2:
Mighta been just the angle the light was hitting it.  :gap:

Slolyfe

#2810
September 19, 2011, 10:34:47 AM
Quote from: fordh8r on September 18, 2011, 11:02:12 PM
Mighta been just the angle the light was hitting it.  :gap:

Or the front seal leaking.
You'll never take me alive

fordh8r

#2811
September 19, 2011, 10:36:00 AM
Or that! :haha:

jrock

#2812
September 19, 2011, 01:09:54 PM
Can't wait to see more :)

Wermz84

#2813
September 19, 2011, 05:56:41 PM
Quote from: fordh8r on September 18, 2011, 10:55:57 PM
Nice shot! Kinda shows the Seepage!  :biggthumpup:

Fixed it for ya. :gap:


It was a nice shot, Cant wait to see more of the pics you and your wife got.  :thumbs:
I like to Drive!

fordh8r

#2814
September 19, 2011, 06:10:19 PM

MiniSimp

#2816
September 20, 2011, 04:38:39 PM
4 or 5 seater ideas... go!

brockbuilt85

#2817
September 20, 2011, 04:40:22 PM
f toy, just do it. or swap your stuff under a 2nd gen 4runner
When in doubt, skinny pedal!
Turd Box Build:
http://board.marlincrawler.com/index.php?topic=50894.0

fordh8r

#2818
September 20, 2011, 05:03:16 PM
Make Yeller take them for you and save the trouble of building another rig! :cheese:

MiniSimp

#2819
September 20, 2011, 05:05:48 PM
Well, I know his suspension is setup right. :greengrin:
Print
Go Up Pages 1 ... 85 86 87 88 89 90 91 92 93 94 95
User actions