Author Topic: master cylinder question for all you toyota pervs. (Read 1515 times)

yotadork83 · « **on:** Oct 03, 2006, 09:08:37 PM »

i have a 90 toyota cressida and today when i looked at the master cylinder it had the 1" stamping on it. just wanted to know if this will work or not.
also the car has rear disk breaks an i was wondering if any body has tryed these befor.

kneedownnate · « **Reply #1 on:** Oct 03, 2006, 10:18:23 PM »

It's quite possible. Glen is using a celica mc and I'm using one from an 87 supra, both 1". Look at the bolt pattern and fitting location to be sure. I had to put a slight bend in one of my lines, but I was able to do it without creasing it.

79coyotefrg · « **Reply #2 on:** Oct 04, 2006, 03:57:34 PM »

yotadork83 · « **Reply #3 on:** Oct 04, 2006, 06:45:24 PM »

allright took a closer look at today and it looks like the bolt pattern is the same. but now it looks like the brake booster is much bigger than my 83 so would the bigger booster do me any good think i am just going to go for it. just wanted to know if it will actually work better or not, because it might be awhile before i get to drive it.

Also took some pics of the rear disk setup and i think that i can make it work on my set up. it has the internal drum brake e-brake system so that is diffently not going to be used.

what do you guys think.

79coyotefrg · « **Reply #4 on:** Oct 04, 2006, 07:00:10 PM »

looks good from here, the master cylinder anyway

dcg9381 · « **Reply #5 on:** Oct 05, 2006, 07:17:50 AM »

Bigger booster will give your brakes more "grab" - watch the outer diameter when installing on a 1st gen, there isn't a lot of room.

yotadork83 · « **Reply #6 on:** Oct 05, 2006, 08:12:54 AM »

thanks that was the anwser i was looking for dosent matter i probley just cut out the inner fender wall.

Author Topic: master cylinder question for all you toyota pervs. (Read 1515 times)

yotadork83

master cylinder question for all you toyota pervs.

kneedownnate

Re: master cylinder question for all you toyota pervs.

79coyotefrg

Re: master cylinder question for all you toyota pervs.

yotadork83 [OP]

Re: master cylinder question for all you toyota pervs.

79coyotefrg

Re: master cylinder question for all you toyota pervs.

dcg9381

Re: master cylinder question for all you toyota pervs.

yotadork83 [OP]

Re: master cylinder question for all you toyota pervs.

Related Topics


	Author Topic: master cylinder question for all you toyota pervs. (Read 1515 times) 0 Members and 1 Guest are viewing this topic. yotadork83 Crawler Guru Turtle Points: 18 Posts: 705 Member since Mar '06 ninja turtules rule!! master cylinder question for all you toyota pervs. « on: Oct 03, 2006, 09:08:37 PM » i have a 90 toyota cressida and today when i looked at the master cylinder it had the 1" stamping on it. just wanted to know if this will work or not. also the car has rear disk breaks an i was wondering if any body has tryed these befor. Logged 83 toyota shortbed, 90 rear axle, 5.29's f/r, spools f/r, 22/20 hybrid w/propane, 37 mtrs. dual transfer cases. http://board.marlincrawler.com/index.php?topic=22712.0 yotas 4 life homie! kneedownnate Gold Turtle Award Turtle Points: 1128 Posts: 9,757 Member since Oct '04 Re: master cylinder question for all you toyota pervs. « Reply #1 on: Oct 03, 2006, 10:18:23 PM » It's quite possible. Glen is using a celica mc and I'm using one from an 87 supra, both 1". Look at the bolt pattern and fitting location to be sure. I had to put a slight bend in one of my lines, but I was able to do it without creasing it. Logged RIP KYOTA You can go through life being scared of the possible, or you can have a little fun and tease the inevitable. Give a man venison, he'll eat for a day. Teach a man to hunt Blacktail, he'll be frustrated for life! 79coyotefrg Rock Ninja Gold Turtle Award Turtle Points: 1452 Posts: 22,633 Member since May '02 Solid axle Toys Rule ! ! ! Re: master cylinder question for all you toyota pervs. « Reply #2 on: Oct 04, 2006, 03:57:34 PM » Logged AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/ 32/36weber, Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears RIP Nitro 9-29-07 I sure miss him $I\'m Down$ MarlinCrawlerInc IS NOT affiliated with TrailGear in any way yotadork83 [OP] Crawler Guru Turtle Points: 18 Posts: 705 Member since Mar '06 ninja turtules rule!! Re: master cylinder question for all you toyota pervs. « Reply #3 on: Oct 04, 2006, 06:45:24 PM » allright took a closer look at today and it looks like the bolt pattern is the same. but now it looks like the brake booster is much bigger than my 83 so would the bigger booster do me any good think i am just going to go for it. just wanted to know if it will actually work better or not, because it might be awhile before i get to drive it. Also took some pics of the rear disk setup and i think that i can make it work on my set up. it has the internal drum brake e-brake system so that is diffently not going to be used. what do you guys think. ray2 059.jpg (75.08 kB, 1456x1328 - viewed 72 times.) ray2 060.jpg (71.41 kB, 1411x992 - viewed 64 times.) ray2 064.jpg (43.64 kB, 1501x778 - viewed 68 times.) Logged 83 toyota shortbed, 90 rear axle, 5.29's f/r, spools f/r, 22/20 hybrid w/propane, 37 mtrs. dual transfer cases. http://board.marlincrawler.com/index.php?topic=22712.0 yotas 4 life homie! 79coyotefrg Rock Ninja Gold Turtle Award Turtle Points: 1452 Posts: 22,633 Member since May '02 Solid axle Toys Rule ! ! ! Re: master cylinder question for all you toyota pervs. « Reply #4 on: Oct 04, 2006, 07:00:10 PM » looks good from here, the master cylinder anyway Logged AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/ 32/36weber, Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears RIP Nitro 9-29-07 I sure miss him $I\'m Down$ MarlinCrawlerInc IS NOT affiliated with TrailGear in any way dcg9381 Rock Master Turtle Points: 0 Posts: 176 Member since May '05 Crawling with Marlin Re: master cylinder question for all you toyota pervs. « Reply #5 on: Oct 05, 2006, 07:17:50 AM » Bigger booster will give your brakes more "grab" - watch the outer diameter when installing on a 1st gen, there isn't a lot of room. Logged d_ginther@hotmail.com www.22returbo.net www.2rzturbo.net yotadork83 [OP] Crawler Guru Turtle Points: 18 Posts: 705 Member since Mar '06 ninja turtules rule!! Re: master cylinder question for all you toyota pervs. « Reply #6 on: Oct 05, 2006, 08:12:54 AM » thanks that was the anwser i was looking for dosent matter i probley just cut out the inner fender wall. Logged 83 toyota shortbed, 90 rear axle, 5.29's f/r, spools f/r, 22/20 hybrid w/propane, 37 mtrs. dual transfer cases. http://board.marlincrawler.com/index.php?topic=22712.0 yotas 4 life homie!