Author Topic: Need torque setting (Read 1546 times)

David · « **on:** Jun 05, 2011, 02:38:46 PM »

83' yota 4x4 5 sp.
Can someone give me the torque setting for the trans output shaft yoke nut?
I'm changing the seal and can't find the info in my Haynes.
Thank you

Peterbuilt84 · « **Reply #1 on:** Jun 05, 2011, 02:52:43 PM »

I think it's 90 ft-lbs

Check the fsm to be sure.

http://www.ncttora.com/fsm/

79coyotefrg · « **Reply #2 on:** Jun 05, 2011, 07:31:46 PM »

I used a 4 foot cheater pipe and it still wasnt tight enough

4RunnerChevy · « **Reply #3 on:** Jun 05, 2011, 07:53:22 PM »

Quote from: 79coyotefrg on Jun 05, 2011, 07:31:46 PM

I used a 4 foot cheater pipe and it still wasnt tight enough

x3

David · « **Reply #4 on:** Jun 06, 2011, 09:28:09 AM »

Thank you for the info.
"I used a 4 foot cheater pipe and it still wasnt tight enough".
A four foot cheater would not tighten it enough, I'm missing something here guys, if it takes 90 or so pounds why would a cheater bar not do the job, is the yoke not seated or stays loose??
Sorry for being dumb but I don't want to mess this up, I just spent a pile of money on this rig and want to it do right.

SFD4x4 · « **Reply #5 on:** Jun 06, 2011, 03:32:25 PM »

I am pretty sure it is 90. I was able to get that with my 1/2" torque wrench and have not had any problems with it. Just checked my 83 FSM, 80-101ft/lbs. Hope this helps.

David · « **Reply #6 on:** Jun 06, 2011, 08:41:10 PM »

Yes it does help and thank you for checking that. I'm going to change it out tomorrow. Thank you guys.

SFD4x4 · « **Reply #7 on:** Jun 06, 2011, 10:37:21 PM »

No prob.

Author Topic: Need torque setting (Read 1546 times)

David

Need torque setting

Peterbuilt84

Re: Need torque setting

79coyotefrg

Re: Need torque setting

4RunnerChevy

Re: Need torque setting

David [OP]

Re: Need torque setting

SFD4x4

Re: Need torque setting

David [OP]

Re: Need torque setting

SFD4x4

Re: Need torque setting

Related Topics


	Author Topic: Need torque setting (Read 1546 times) 0 Members and 1 Guest are viewing this topic. David Rock Master Turtle Points: 218 Posts: 263 Member since Jan '03 I love Marlin Crawler! Need torque setting « on: Jun 05, 2011, 02:38:46 PM » 83' yota 4x4 5 sp. Can someone give me the torque setting for the trans output shaft yoke nut? I'm changing the seal and can't find the info in my Haynes. Thank you Logged Peterbuilt84 The 1K Club Turtle Points: 12 Posts: 1,049 Member since Sep '09 Re: Need torque setting « Reply #1 on: Jun 05, 2011, 02:52:43 PM » I think it's 90 ft-lbs Check the fsm to be sure. http://www.ncttora.com/fsm/ Logged My Build: http://board.marlincrawler.com/index.php?topic=71999 79coyotefrg Rock Ninja Gold Turtle Award Turtle Points: 1452 Posts: 22,633 Member since May '02 Solid axle Toys Rule ! ! ! Re: Need torque setting « Reply #2 on: Jun 05, 2011, 07:31:46 PM » I used a 4 foot cheater pipe and it still wasnt tight enough Logged AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/ 32/36weber, Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears RIP Nitro 9-29-07 I sure miss him $I\'m Down$ MarlinCrawlerInc IS NOT affiliated with TrailGear in any way 4RunnerChevy The 1K Club Turtle Points: 5 Posts: 1,426 Member since Sep '08 Santa Cruz Mountains Re: Need torque setting « Reply #3 on: Jun 05, 2011, 07:53:22 PM » Quote from: 79coyotefrg on Jun 05, 2011, 07:31:46 PM I used a 4 foot cheater pipe and it still wasnt tight enough x3 Logged 1986 4-Runner https://www.facebook.com/SantaCruzWheelers David [OP] Rock Master Turtle Points: 218 Posts: 263 Member since Jan '03 I love Marlin Crawler! Re: Need torque setting « Reply #4 on: Jun 06, 2011, 09:28:09 AM » Thank you for the info. "I used a 4 foot cheater pipe and it still wasnt tight enough". A four foot cheater would not tighten it enough, I'm missing something here guys, if it takes 90 or so pounds why would a cheater bar not do the job, is the yoke not seated or stays loose?? Sorry for being dumb but I don't want to mess this up, I just spent a pile of money on this rig and want to it do right. Logged SFD4x4 Rock Master Turtle Points: 4 Posts: 218 Member since Mar '10 Re: Need torque setting « Reply #5 on: Jun 06, 2011, 03:32:25 PM » I am pretty sure it is 90. I was able to get that with my 1/2" torque wrench and have not had any problems with it. Just checked my 83 FSM, 80-101ft/lbs. Hope this helps. Logged 83 pickup, 4.88s, chevys in rear, RUF, Dual Transfers, flat belly, 3RZ swap, disc brake x4, rollin on 36" irocs IF YOU SEE A 20' PAC WEST/CARSON FLAT BED TRAILER FOR SALE CHECK OUT THE STOLEN SECTION. IT MIGHT BE MINE!!!! David [OP] Rock Master Turtle Points: 218 Posts: 263 Member since Jan '03 I love Marlin Crawler! Re: Need torque setting « Reply #6 on: Jun 06, 2011, 08:41:10 PM » Yes it does help and thank you for checking that. I'm going to change it out tomorrow. Thank you guys. Logged SFD4x4 Rock Master Turtle Points: 4 Posts: 218 Member since Mar '10 Re: Need torque setting « Reply #7 on: Jun 06, 2011, 10:37:21 PM » No prob. Logged 83 pickup, 4.88s, chevys in rear, RUF, Dual Transfers, flat belly, 3RZ swap, disc brake x4, rollin on 36" irocs IF YOU SEE A 20' PAC WEST/CARSON FLAT BED TRAILER FOR SALE CHECK OUT THE STOLEN SECTION. IT MIGHT BE MINE!!!!