Topic: Project BoostedRunner, SOLD

[wakkjobb]

Don't hold it for me; I need a job before I buy anything for my pile...

>>Dan

[pumkin toy [OP]]

ya my bad i seen the drilled and tapped and the word steering and got all excited man...LOL well thats sick anyway dude. Assist will be way better than normal. Not normal as in when tim used to wheel wit push/ pull old school... HA HA that was good time's. Normal as in how we are set up now. So maybe ya could sell my bro your old ifs box dude and he could buy my hy steer for his runner... LOL i might even give him my hysteer for christmas i'm thinkin. since i won't be needin it anymore..

Well post some pics up of the front dove man. I was over the other night and it looks way sick and the full size width is gonna be dope. I dig the dove brah!! Ya get the other side of the front bumper mean guy look short n up and back on?? Well progress is lookin good anyway dude, keep it up! 

yeah full hydro wouild be cool, but i dont have a grand to dump on a full hydro kit!  i will sell him my old box if he wants it.

pics

i will get some soon, im still getting the new computer all setup

[pumkin toy [OP]]

Don't hold it for me; I need a job before I buy anything for my pile...

>>Dan

ok

[pumkin toy [OP]]

I took a few pics with my phone tonight.  I dont really have enough room in the garage to back up and take a good pic.  I narrowed the front six inches on each side.  Basically cut out the hole in the inner structure where the headlight goes and sectioned it back together.  I also cut five inches out of the bumper hoops on each side and tacked them back on.  I swooped them back a bit closer to the grill than before and it looks really gnarly.  I also took a couple pics of the drilled and tapped steering box that I got for 50 bucks.

[pumkin toy [OP]]

Few more.........     where I have the tires sitting is real close to what the actual stance will be when I put the 80 series axles under it.  the new setup will be five inches wider than the mini axles were. I'm also lowering the ride height one inch and moving the front axle forward probly two more inches.

[minicrawlin]

BAM dude!! thats sick i gotta get over there to scope that man looking good for sure! i like the front end alot better.
where'd you pick that box up for 50 bones thats a steal!!

[NITE KRAWLERS]

Dude its gonna be sick man!! For some reason the front bumper hoops and stinger remind me of that one dude in the movie watchmen wit the mask...Weird but it does brah!!

[COToy91]

Are you just running a Taurus fan in reverse? I have a 4.3L in my truck and it starts to get a little hot when crawling, but it runs fine at faster speeds.

Is it keeping your 7mgte cool on the trail? What outdoor temps have you ran trails at? Some trails get 100+ around here in the summer.

[gnarrkill]

looks dope 

[Uncle Ben]

Me likey!  That looks really mean!

[THK Matt]

LOOKIN DOPE!

[bigarms23]

love the way its coming out

[pumkin toy [OP]]

BAM dude!! thats sick i gotta get over there to scope that man looking good for sure! i like the front end alot better.
where'd you pick that box up for 50 bones thats a steal!!

yeah man you should come look at it!  I got the box from Todd Zick over at Z fab off-road.  He has a shop over by ACE steel.

Dude its gonna be sick man!! For some reason the front bumper hoops and stinger remind me of that one dude in the movie watchmen wit the mask...Weird but it does brah!!

not sure who you are talkin about man!

Are you just running a Taurus fan in reverse? I have a 4.3L in my truck and it starts to get a little hot when crawling, but it runs fine at faster speeds.

Is it keeping your 7mgte cool on the trail? What outdoor temps have you ran trails at? Some trails get 100+ around here in the summer.

honestly idk for sure what kind of fan it is.  I have not had a problem with overheating on the trail though. Its been through some 100 degree days out crawlin and never had a problem

looks dope 

Thanks man! I'm liking it alot more

Me likey!  That looks really mean!

It is mean! ha ha  I cant wait to have the back done too.  Thats gonna be a pain though

LOOKIN DOPE!

love the way its coming out

Thanks dudes!

[twistedtoy92]

hell yeah! If I only had a tube bender I'd have the front dove of my 92 done.... Rigs lookin floppin' MEAN!!! I like it!

[pumkin toy [OP]]

hell yeah! If I only had a tube bender I'd have the front dove of my 92 done.... Rigs lookin floppin' MEAN!!! I like it!

thanks bro!    My new clutch should be here friday, I'm hoping to get the whole drivetrain put back in this weekend

[Jordan7118]

I'd like some more pics of the front dove in progress. Got any? I know you explained it, but pictures are worth a thousand words 

[pumkin toy [OP]]

I'd like some more pics of the front dove in progress. Got any? I know you explained it, but pictures are worth a thousand words 

I didnt take any pics of it in progress,  I just started doing it and whipped it out in about three hours, 9excluding time to move all the wiring harnesses and junk out of the way)

So I got my clutch today and its the wrong one. I dont know for sure which clutch I need to order for this swap. After seeing the clutch that came for the 7mgte application, I'm thinking that maybe I just need a clutch for a 22ret.

[NITE KRAWLERS]

I have a 22re but if you think you need one for a 22ret i'm sure i don't! My clutch is not really that good but you could compare to wat you have and wat you got and all that. But again if you mean 22ret i don't have that one! Also that sucks its wrong really cause i know your wantin to get the tranny and cases back in der!! Well good luck and give a shout if yo need any thing man.

[SCyotacrawler420]

you need the clutch from the 7mge (non turbo) 86-89 supra. cause the 22r series are too small an the 7mgte is oviously from a different world compared to what were use to seeing.

[SCyotacrawler420]

i love the dovetail front end by the way. it reminds me exactly of my truck, i think everyone should dovetail there truck, ha. it makes it look alot wider too

[81_yota]

that thing is sick lookin love what ya done

[THK Matt]

you need the clutch from the 7mge (non turbo) 86-89 supra. cause the 22r series are too small an the 7mgte is oviously from a different world compared to what were use to seeing.

90-92 N/A clutch wont work?

[pumkin toy [OP]]

you need the clutch from the 7mge (non turbo) 86-89 supra. cause the 22r series are too small an the 7mgte is oviously from a different world compared to what were use to seeing.

yeah i'm thinkin thats the clutch I need. The 22r and 22re clutch disks have an 8 7/8" diameter and the 22ret clutch disk has a 9 1/4" diameter. I found out that a guy I know has a 7mge clutch at his house and i'm going to compare my clutch to it on monday.  I found out that the dimensions of the 22ret clutch disk are the same as the 7mge, so that clutch could potentially work too, but idk if it will match the supra flywheel.
 

i love the dovetail front end by the way. it reminds me exactly of my truck, i think everyone should dovetail there truck, ha. it makes it look alot wider too

thanks dude, i'm really liking how its turning out too!

that thing is sick lookin love what ya done

Thanks man!

90-92 N/A clutch wont work?

Yeah I think it will, but something convinced me to order a turbo clutch instead, that was a bad choice!

[SCyotacrawler420]

idk if the 22ret clutch will work... the pressure plate might bolt up differently to the 7mgte. i dont actually know for sure. but the 90-92 7mge clutch works also.

where do you live? im curious as to what your truck is like compared to mine an was seeing if we could compare. i got links front an rear an full widths. but same motor an tranny an THE DOVETAILED FRONT! ha

[pumkin toy [OP]]

idk if the 22ret clutch will work... the pressure plate might bolt up differently to the 7mgte. i dont actually know for sure. but the 90-92 7mge clutch works also.

where do you live? im curious as to what your truck is like compared to mine an was seeing if we could compare. i got links front an rear an full widths. but same motor an tranny an THE DOVETAILED FRONT! ha

Well damn!  why couldnt you have told me that info before I ordered the wrong clutch? lol   I live in Rapid City South Dakota.  I'm assuming you live in California?  Most people on this forum are from Cali.

[SCyotacrawler420]

ya, i was a little late on that one... return it  an south dakota is pretty far. but i would be down to drive out there. i love visiting new places. an ya, im a cali kid.

[Uncle Ben]

ya, i was a little late on that one... return it  an south dakota is pretty far. but i would be down to drive out there. i love visiting new places. an ya, im a cali kid.

Be sure to haul your crawler up there with you!  You will be very happy you did!!!!

[pumkin toy [OP]]

ya, i was a little late on that one... return it  an south dakota is pretty far. but i would be down to drive out there. i love visiting new places. an ya, im a cali kid.

Yeah its all boxed up and ready to go back! Its a long drive to SD from CA.

Be sure to haul your crawler up there with you!  You will be very happy you did!!!!

Yes sir! lots of good wheelin here

[SCyotacrawler420]

oh, i wouldnt think twice about taking the crawler out there, i would even bring a full spare set of tires an a bunch of parts. it is a pretty far drive but oh well. its worth it. i can then hit up rubicon, fordyce an colorado on the way out there

[pumkin toy [OP]]

oh, i wouldnt think twice about taking the crawler out there, i would even bring a full spare set of tires an a bunch of parts. it is a pretty far drive but oh well. its worth it. i can then hit up rubicon, fordyce an colorado on the way out there

sounds like a great round trip!