0 Members and 4 Guests are viewing this topic.
I also taught him how to put in 5min of hard work and then spend 15min staring and admiring what you have done...
Ok folks. I was just wondering what you all think is the best all around position to mount rear shocks. I have installed 4 marlin springs (front and back) and I have the 14 Bilstein gas shocks. Installed the front shocks with extended hoops. And am currently driving with no rear shocks . According to info in the box you are supposto have 60% of the shock rod in the tube at ride height thats 8.4. Which means 5.6 of rod showing when every thing said and done (about 26eye to eye). I dont really want to cut a hole in the center of my truck bed and have about ¾ sticking out for the upper shock mounts.Also Ive been told that if your shocks are mounted like an upside down V (/\) your rig kinda wonders around at higher speeds. Any pics, suggestions, and alternatives to the upside down V thing would be great . O by the way Its an 83 pickup
Best for articulation is how AaronB has his. Best for street, would be almost vertical. I also would go with a 12" shock, and if it sees a lot of DD duty, run them like this / \ not as drastic an angle as Aarons, space out the top mounts mabye 6 inches or so. That'll give you more use out of the shock, but still allow decent articulation off road.
If you want you can french a piece of square tube and incorporate the upper shock mounts into it and use it like another cross member and that will give you a little more room for taller shocks set up like this / \.
what valving would you use. like if you were goin to use bilstein 5150s. they have a 255/70 or the 160/60 valving DRew
I think what I'll do is before I welt in the upper cross brace(upper shock mount) i will drill a serries of mounting holes. from dead center out 1" and every inch up to 4".. which will give me 5 different possitions to mount the upper portion of the shocks.. also BLACKDOG do you knowhow much up travel the the rear 4" marlin leafs are suppose to travel (w/ 6" shackles)?? I haven't set the bump stops in yet to the U bolt plate. I want the bump stops to limit the up travel not the shocks
I think I know what you are saying about "french"... do you mean cut a hole in the tube and bend or flare the sides to fit the shocks??
I am re-doing my rear 14" shocks right now and here's what I did.get some trailer shackles from agriculture store and cut em in half. (these are now the tabs to weld onto the top of your axle and bolt the shocks in)... bottoms are done now.cut a hole in the flatbed expanded steel and stand shock up through it. Done now.get trailer leaf springs hangers that are 1.25" wide and bolt them to the top of the shock... weld that to your chassis however you want to. I'm probably gonna use some small tubing and a 1/4" gusset
i always thought that the "best way" was to mount the shocks verticle , thats what i am going to eventually do, that is whenever i decide to put rear shocks on
Unfortunately I don't, but it is really going to be different for every vehicle anyway. a standard would give you an idea, but it's going to depend on how broken in the springs are, shackle lenght like you already mentioned, even your bedload will make a difference. When the bed is unloaded, it is fairly light, so the springs are more likely to not flex as much and cause the truck to flex more at the front, since it is heavier due to the engine. Loaded, it'll flex better out back, due to the added resistance of the weight. Your best bet IMO for setting your bumpstops is to load the bed with an approximate wheeling weight (cooler, tent, tools, etc. Just use your best estimate) and then flex it out to where your shocks are almost completely compressed. Then measure the distance, and mount your bumpstops accordingly.
This is how i have mine mounted, i used to have them mounted just like aronb"s truck, I found that it is more stable like this And i am not even close to maxing them out(all the way flexed).
Kind of but you will need to buy the short axle shock mounts, completely cut out the portion of tubing and weld in the mount into the tubing, or you could just cut out the bottom side of the tubing and drill some holes to bolt the shocks up.
you want them as straight up as possible for better handling/body roll.
I finished them tonight. they aren't beautiful but they are strong and they took 1 hour and $5 to do it.pics tomorrow
Started by 84_yota_4wd Toyota Pickup/4Runner Tech 1979-95
Started by Yota Up Toyota Pickup/4Runner Tech 1979-95
Started by birfection Newbie Questions
Started by 24SHORTIE Newbie Questions
Started by padilla95624 New Member Check-In!