sure its been covered, but search didn't trun up anything. Third member ???

Started by BLACKDOG, December 02, 2005, 04:03:59 PM

0 Members and 1 Guest are viewing this topic.

Print
Go Down Pages1
User actions

BLACKDOG

December 02, 2005, 04:03:59 PM
1. Will a v6 3rd fit into a 4cyl housing without clearancing?  what needs to be clearanced if it doesn't?

2. are front and rear 3rds interchangable, or are they different?
:usa: Its better to die on your feet than live on your knees :usa:

"Freedom is never more than one generation away from extinction. We didn't pass it to our children in the bloodstream. It must be fought for, protected, and handed on for them to do the same, or one day we will spend our sunset years telling our children and our children's children what it was once like in the United States where men were free. "

"I don't believe in a government that protects us from ourselves."
              -Ronald Reagan

Don't take life too seriously, it isn't permanent

yotacrawler4

#1
December 02, 2005, 06:20:26 PM
yes third members (8'') 79-95 are all interchangable and no u dont have to do any clearancing, i just did a V6 third and a high pinion in my truck :turtle:  :beerchug:
86' yota, extra cab, duals, HP frnt with detroit 4.88s, V6 rear with detroit 4.88s, bobby super set, driveline tech dl's, neat lil upgrades on the way can someone say 4link and dovetail front...

79coyotefrg

#2
December 02, 2005, 06:25:37 PM
Quote from: BLACKDOG on December 02, 2005, 04:03:59 PM
1. Will a v6 3rd fit into a 4cyl housing without clearancing? what needs to be clearanced if it doesn't?

2. are front and rear 3rds interchangable, or are they different?
swap away there Blackdog,  i just installed a 4.37 4cyl ring gear on my elocker,

had to make a custom sleeve,  and i need to refit some things befor installation but i think it'll work great
AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/    32/36weber, :driving: Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears    RIP Nitro 9-29-07 :(  I sure miss him :down: MarlinCrawlerInc IS NOT affiliated with TrailGear in any way

Rocksurfer

#3
December 02, 2005, 06:27:55 PM
 :werd: :imwithstupid:
The Ghost-Rider/Ghost Runner

No matter how far you fall, the ground will always catch you

toyo487

#4
December 03, 2005, 08:15:51 AM
I just put V6 thirds in my 4cyl,  the front and rear went with ease.  The V6 thrids that I found had the 4.88's and  I did no clearancing to fit.  Good luck
1986 Toyota 4Runner 22re 5spd transmission and dual transfer cases (4.7's in the rear). E-lockers front and rear.

2005 GMC Sierra diesel, compound turbo setup to pull.

   God gave all people talents but the only one who can find them is you.

Prismo

#5
December 03, 2005, 08:19:57 AM
I have a turbo truck third member in the back of the runner, Swaps right in.
Retired Great White Turtle Hunter
Originally posted by fortysixandtwo – sheesh, you should see the transvestites i sell ammo to sometimes

kyle_22r

#6
December 03, 2005, 09:04:35 AM
i'm gonna put a V6 4.88 3rd member in my front axle.  on test fitting it i found that it wouldn't go in.  i figured out my problem, the flange for the 3rd member is double thick, and while the top layer of the bottom notch was cut out, it was barely cut on the bottom layer.  i took my angle grinder to it and all is well

Prismo

#7
December 03, 2005, 09:23:07 AM
What year axle Kyle?
Retired Great White Turtle Hunter
Originally posted by fortysixandtwo – sheesh, you should see the transvestites i sell ammo to sometimes

kyle_22r

#8
December 03, 2005, 10:05:46 AM
79.  i think it was just a factory screwup, no big deal.
Print
Go Up Pages1
User actions