Topic: Dean's 3RZ swap

[4THEWKN]

This Project is featured in our Official 3RZ Knowledge and Database Thread


The new motor finds a new home!

[4THEWKN [OP]]

Motor mounts  

[4THEWKN [OP]]

Swapping to 96 2wd T100 oil pan

[4THEWKN [OP]]

Motor installed

[4THEWKN [OP]]

More motor pics

[4THEWKN [OP]]

Fuel lines to tank 

[BigMike]

nice, it's about time I see some pictures of this thing

[TrackVino]

This thing still not running?

What are you waiting for     

Time is running out, you think you will have it running by Sunday? ohh, im sorry, I think your way behind, that was Sunday a month ago.

              

[4THEWKN [OP]]

Ya,  I fell and broke my knee & left hand so it's been slow going. It sould be running in a couple of week's........Dean

[BlueRubi]

Cool graphics, you're gettin pretty good with that computer : )........

[4THEWKN [OP]]

That's thanks to trackbeano.....Dean

[BigMike]

Hey Dino,

Can I get some pics of the exhaust around the bellhousing please? Thanks!Image hosted by Photobucket.com

[4THEWKN [OP]]

Hre ya go Mike .I played in the garage a couple of hours  with the exaust it's going to be a tight fit ....Dean

[4THEWKN [OP]]

With the driveline

[4THEWKN [OP]]

I ended up cutting about an 1.5" off of the header. but i think I"m going to leave this to the pro"s ..........Dean

[RHG]

wow, New 3rz, new tranny...you got some new boxes behind that tranny too? Your exhaust is going to look like a snake to get around that drive train. Sure looks perty

[toyhatsu]

Are you going to knock out the plug and mount a T100 rear sump dip stick?...reminds me that the plug is still in the bottom of my oil pan.  Check my parts #'s in BigMikes big project.  If you can't find a good plug for the front, I used a 158gr .357 cast semi wadcutter and hammered it in

PS:

My swap looks like it was done by Homer Simpson compared to that...beautiful!

[BUDDERS]

I like you're fuel line setup way better than mine.  Makes me consider want to do mine right before the truck gets running. 

I can't tell by the pictures if you have a A/C compressor hooked up - have you planned that out yet?

Also, are you going to run the factory evap system or have you planned that out either?

I'm not trying to sound like a smart ass,  I'm just in the middle of the same conversion and would like some input.

[4THEWKN [OP]]

The motor I found only had 8000 miles on it. Really like that part!!!  Even looked like the owner had the first oil change at the dealer or they used a Toyota oil filter. The trans is a SuperTaco W56 HD. What in the world is that you ask!! Well instead of using a W59 Taco trans. We took the W59 main shaft, which is 26 spline and used it instead of the W56 21 spline main shaft. Why??  Because now I can run a 23 spline crawlbox and 23 spline t-case using a Taco 26 spline to 23 spline 34-4gt adapter coupler. This set-up is nice because now every thing in the t-cases is 23 spline.. The W59 bellhousing has to be used also because the starter is on the drivers side.

[4THEWKN [OP]]

The dip stick was a weird thing.. I bought the 96 T100 dipstick and dipstick tube but found that the dipsticks were the same. And that the dipstick tube was different. So I looked in the factory Manuel to find how much oil it takes with this pan . After it's fired up I'll mark the dipstick. As for the AC. I'm going to try to use the 85 system with the 04 compressor. Well see what happens.

[4THEWKN [OP]]

Today I swapped in the 4.88 third and remove the 4.10 third.

[4THEWKN [OP]]

The new chrome grill and now turn signals went on with the bumper and winch.

[BUDDERS]

LOOKIN REAL PURDY DEAN.  Keep up the good work!

[jr9162]

The motor I found only had 8000 miles on it. Really like that part!!!  Even looked like the owner had the first oil change at the dealer or they used a Toyota oil filter. The trans is a SuperTaco W56 HD. What in the world is that you ask!! Well instead of using a W59 Taco trans. We took the W59 main shaft, which is 26 spline and used it instead of the W56 21 spline main shaft. Why??  Because now I can run a 23 spline crawlbox and 23 spline t-case using a Taco 26 spline to 23 spline 34-4gt adapter coupler. This set-up is nice because now every thing in the t-cases is 23 spline.. The W59 bellhousing has to be used also because the starter is on the drivers side.

Is this tranny going to be a Marlin offering? What all is entailed if one is not using a crawler, just the 23 spline Tcase?

[Cheesemaker]

It's cool to finally see some pics of your truck Dean!  Can't wait to get down there next summer, and ride in the beast!  The boys aren't excited about visiting the family, all I hear from them is all about going to Disneyland!  I'm ready to go for a ride.  Oh! Shall I bring the BBQ??     Later Ryan!

[TrackVino]

Already starting another project, but still cant get the first one done!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!


 

[Rockdiver]

Speaking of Projects Dean    I have a Toyota bed that would make a good Flower planter for you  Weeds are over growing it   Lynn

[4THEWKN [OP]]

Dude I totally forgot!!!! Call me tomorrow at the shop.

[Rockdiver]

Hey Dean looks great  I am wondering why I sunk 2500 $$$ into my 22re motor when you could have done this for me   so How about a ford  & 2  22re  motors  for one like yours  installed  Lynn

[4THEWKN [OP]]

If your buing the motor let's talk. I would wait a couple of weeks and you can drive mine to see if you like the motor.