6 Stud Knuckle Photos

[Marketing]

Here are a couple of photos of the 6 stud knuckles we have been working on here at the shop...

[derek]

kick ass!
is this a whole new knuckle or a stock one with some material added then machined down.

derek

[mr4x42u]

cost?Can the current cross over arms be modified or do you have to buy new ones?

[KYOTA]

Kick ass! Didnt I read that these will be around $150?  lets see the arms. Sean thread on PBB said they will included tabs to weld on most arms and they are going to make 6 bolt arms too.

[4RnrRick]

Please excuse me while I clean my keyboard off..... 
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.

NICE!!!   
Now thats one sexy knuckle!

So have the prototypes been tested? How long? by who?
Are the castings x-rayed?
When is the expected date of sale?
How much?
.
.
.
Oh and why did you tell me about this when I busted my ass trying to figure out how to get a 5th stud in the fill hole plug!! Which btw is now finished.

[Marketing]

kick ass!
is this a whole new knuckle or a stock one with some material added then machined down.

derek

This photo is a stock knuckle that has been modified. The production knuckles will be all new and thicker (in the housing) than the stock knuckles.

[Marketing]

cost?Can the current cross over arms be modified or do you have to buy new ones?

Target price is $150 per knuckle. Tabs will be developed that allow stock arms to have two aditional holes.
We also plan to make 6 hole steering arms.

[Marketing]

Please excuse me while I clean my keyboard off..... 

NICE!!!   
Now thats one sexy knuckle!

So have the prototypes been tested? How long? by who?
Are the castings x-rayed?
When is the expected date of sale?
How much?
.
.
.
Oh and why did you tell me about this when I busted my ass trying to figure out how to get a 5th stud in the fill hole plug!! Which btw is now finished.

No these have not been tested yet.
Castings will get lot tested, we are not planning to x-ray each part.
Still working on production, it's gona be awhile yet.
Our target price is $150 each knuckle, not including arms.
We are looking at 6 hole forged and Billet high steer arms.
Also those that already have arms will be able to use an inexpensive weld on tab.

FYI these will be thicker than stock cast knuckle so they will be stronger.

[trailtoy]

This photo is a stock knuckle that has been modified. The production knuckles will be all new and thicker (in the housing) than the stock knuckles.

Chris, is it an actual modified knuckle or did you do some Chopping to a stocker??

[Marketing]

This photo is a stock knuckle that has been modified. The production knuckles will be all new and thicker (in the housing) than the stock knuckles.

Chris, is it an actual modified knuckle or did you do some Chopping to a stocker??

The one in the photos above is a stock knuckle that had a plate added to the top. The fininshed product will be all new material.

[RUFF]

Chris you guys need to seriously think about making the steering arms suit both Left and Right hand drive vehicles. Its not hard to do just make both arms with 2 TRE holes. There is a market for these in Australia and i imagine a few other countries as well.

[Marketing]

The shipping and duty fees make it too expensive. A set of high steer arms cost $199 here in the US. The same arms sent to Oz cost them around $500. At this price they are just too expensive to sell in any volume.

[Willy Mammoth]

Chris, Could you license another company to make them over there? Just a thought

[RUFF]

The shipping and duty fees make it too expensive. A set of high steer arms cost $199 here in the US. The same arms sent to Oz cost them around $500. At this price they are just too expensive to sell in any volume.

I would say $450Aus landed here at the most and for a decent set of arms this is cheap. I think you would be surprised how many people would buy these if they were available. There is a hell of a lot of Companies here now importing custom Products from the US.

[Overlord]

Will these work for Land Cruisers?  FJ60 in particular.

[Marketing]

Will these work for Land Cruisers?  FJ60 in particular.

Yes they will work on FJ40 & FJ60/62's.

[RCKSQRL]

anything new on this chris?

[BigMike]

I've seen the 6 bolt steering arm

[RCKSQRL]

now that is jus cruel.....

[Skinny_Pedal]

i hope we get the word soon. rather cash out for 6stud than 4 stud

[dirtbag]

  so are these to make the front axle IFS-width? 

[Hyena]

Nope, the nuckles will be the stock size, just with 2 more studs added.

[toybuilt]

I've never even hured of this before, is asome

[awhotrods]

This photo is a stock knuckle that has been modified. The production knuckles will be all new and thicker (in the housing) than the stock knuckles.

Damn, everytime I order something from you guys, you come out with a better part a few months later!!  I just installed your high steer a few months ago, but this looks badass!!!

[79coyotefrg]

Damn, everytime I order something from you guys, you come out with a better part a few months later!! I just installed your high steer a few months ago, but this looks badass!!!

hey send me your highsteer  then buy the new six bolt

[awhotrods]

hey send me your highsteer then buy the new six bolt [/quote





     

[WHITE_TRASH]

Ive got allpoo crap on my junk now and once the 6 stud becomes available guess whats gonna happen.

[BigMike]

Ive got allpoo crap on my junk now and once the 6 stud becomes available guess whats gonna happen.

You are going to build a "I Love All Poo" shrine??

[mr4x42u]

Ive got allpoo crap on my junk now and once the 6 stud becomes available guess whats gonna happen.

I forgot you had a bent drag link or somthing from them don't ya?

[WHITE_TRASH]

Yup I bent the tierod pretty good.  Nothing hit the link either, if it did Im sure it would have at least scratched the rattle can off of my front housing but there is no scratches.  My only guess is my strong arming of the wheel did it in.  Adrenaline and beings pissed off will do damage.....