Topic: Parting out 84 Toyota 4x4 desert race truck

[The_Blue_Coyote]

 <- Parting out this 1984 Toyota 4x4 Desert race truck - lots of good stuff for sale

1 - 22ret bell housing (R series trans to 22r) - no cracks $175

2 -  Aquilla low steer cross over arm $125 - and for an extra $25 I will include the braced LH arm and tie rods

3 - Deaver long travel front springs- 12" wheel travel, about 4" of lift, uses stock pivots, includes 5/8 U bolts and special dogbone shackels. These are Deaver springs - the best leaf springs made $400 for the set up.

3b - Deaver G50 (58" Ranger) rear leaf springs - 16" travel. Inc 5/8 ubolts and top pivot shackles - $450

4 - Toyota rear axle - 95 V6 housing, braced top and back, V6 third member w/ 5.29 and Yukon spool, V6 axle shafts, TSM disc brakes, 5/8 wheel studs. Recent bearings in diff and axle. $650

5 - 22re Barstow Duty motor and x-fer case mounts - forget Xteme duty, these were made to withstand Barstow! Uses urethane bushings. Full set $150

6 - HD drive lines with big pattern - $65 each (lengths pending)

7 - 22re stand alone wire harness - plugs into engine, and hook up power, switch, fuel pump. Great for a tube buggy or a rail. Includes all relays, ECU, all wires labeled. $250

8 - Toyota fiberglass fenders - 84 to 88, made by Hannaman, large wheel opening, have some cracks but very useable- $75 pair (have 2 pairs)

9 - Toyota frame / roll cage / sheet metal - entire race frame with all of the race approved roll cage (1.75 x .120 mild steel) with the cab, fenders, bed sides, doors, bumpers. Great start for that project as the cage work is done. Set up for Beard seats, 22re, R trans, Ranger leafs, etc $650

10 - Toyota R150 V6 transmission - no bell housing. Mileage unknown $150

All parts located in Elmira OR - just west of Eugene OR

email me at bluecoyoteracing@earthlink.net for more info and photos

[minicrawlin]

dam i wanna build a desert truck!           ha ha

Bump for sweet parts someone will want, good luck!

[dune_it86]

hey how close is elmira to albany? i want the aquilla steering arm! let me know asap please!!! lol

[The_Blue_Coyote [OP]]

hey how close is elmira to albany? i want the aquilla steering arm! let me know asap please!!! lol

Just west of Eugene. It is about 45 miles to Albany.

[Kentucky Jelly]

Willing to ship a set of fenders to central California?

[dune_it86]

blue_coyote, hey i called u after i posted lol thanks for the help, will you pm me your address so i can send u the check for the steering arm? thanks again!

[SUBCOOL420]

Any fenders left?  If so how much to send to zip 22714?

Thanks 

[Thomas P]

im heading that way june 21, from nor cal, if anyone wants me to haul something, i wants some fenders if they are still around by then!!

[joey0712]

Do you still have the harness and computer?

[The_Blue_Coyote [OP]]

Getting back to evey one:
dune_it86 - Check your email

Posted by: SUBCOOL420 - let me weigh them tomorrow

Thomas P- if I get lots of interest I will steer buyers your way - so you can make gas $.

joey0712- yes - ECU, all relays, stand alone wire harness still avaialble.

Have gotten lots of emails on the fenders.
Taking a huge truck load to the Coburg hi performance swap meet on Sat - if you want something speak up now....

[bleakhorizon]

gota  pic of the frame and and cage....

[joey0712]

Ok my buddys need it for a buggy. I will ge back to you thanks.

[The_Blue_Coyote [OP]]

gota  pic of the frame and and cage....

This is the truck still assembled - just remove the suspension, fuel cell, seats, lights, tires, steering etc. Dash will be included but w/o gauges. Plumbing will be included less the fuel pumps, stainless braid lines, brake lines, etc. Of course anything can be purchased and can stay attatched. Cage is 1.75 x .120 mild steel and is race legal -been tagged by CORR, ROR and by ARTS for MORE and MDR.

[dune_it86]

thanks i am sending it out, my brother can probably meet u on I-5 near albany to pick it up, while your on ur way north to salem if thats alright with you...

[joey0712]

Any chance you still have the harness.... If so pm me.

[Thomas P]

im heading out your way on June 20th from nor cal, and i can haul parts for anyone if needed, and i am still wanting a pair of fenders if they are still available, ill have cash let me know