Marlin Crawler Dual Case Interior Picture Gallery Submission Thread

[Gixxer Jon]

Here is the newest configuration in my 2005 Tacoma.  It has the all new Marlin crawler w/the t360 and 4.70 gears and an FJ cruiser t-case.  And it all works like a dream!  Thanks Marlin Crawler.  Your the best!

I knew that cup holder had a purpose! lol Looks great

[AWSUMDC]

Here is one we did in Chorizo Dan's 02 Tacoma.

[AWSUMDC]

Here is the DeMello-Offroad Fj Cruiser with a Marlin Crawler installed by RockSolidToys.





This is one of the only Fj Cruisers that is still IFS with a crawler box and the stock transfer case.

[swapped89]

Here is one that I made. (1989 std cab pickup)

[brockbuilt85]

NICE!
are those boots the stock ones or did you pick them up somewhere else?

[earfarmer]

All of those look very nice!  Thanks for the great ideas on what to do with mine:)

[swapped89]

NICE!
are those boots the stock ones or did you pick them up somewhere else?

Ya the front two are stock boots. Cut in half to make room for the doubler. If you don't cut them in half. I was havin problems with the tranny shifter popping out of the forward gears. And the twin stick boots are TG. And they're all siliconed onthe bottom so it's pretty much air/dust tight.

[ajordan1975]

Here's mine. 85 standard cab.

[brockbuilt85]

Ya the front two are stock boots. Cut in half to make room for the doubler. If you don't cut them in half. I was havin problems with the tranny shifter popping out of the forward gears. And the twin stick boots are TG. And they're all siliconed onthe bottom so it's pretty much air/dust tight.

and its a piece of sheet metal that they are attatched to? i really like it, its simple, but good lookin!

[swapped89]

Ya first I just sat the cut boots over the shifters. Taped them all together so they would be in the correct position when I took the boots out. Made a cardboard cutout to hold the boots. Then transfered the cardboard design to a piece of sheet metal. Some paint, silcone, foam strip and walaaa.

[CSR73]

Mine's not as clean or pretty as some of the fine rigs above.  I'm not sporting the knob because I didn't get one with my order.  (BigMike, can you hook me up?)

My '81....

[Yota Rolla]

here's my stick setup not near finished still have to do some cutting on the floor

[slander]

My stick/change holder/setup on my 02 tacoma!  

[FRANKENYOTA91]

After looking at these i really need to get off my  and get mine done. i just have a big whole cut in the floor 

[khagerty]

1958 Xtra cab

[khagerty]

85 Xtra cab yota

[BigMike]

Nice

[Wermz84]

Good looking stuff in here.  Man I really go for the minimalistic approach with mine.

[ninjasyota]

Here's mine. 85 standard cab.

Lol, I have that little green dude too, it was on my stinger, but it was too distracting, so he is going to live on top of my rear diff now!! (he can scare people behind me!!)

[Cheesemaker]

This a R151F with a single with twins.  But I need to have the sticks bent to make it work.  This just me fabbing things.

[BigMike]

Man I really go for the minimalistic approach with mine.

2WD?

[Cheesemaker]

  Sorry I missed the "dual case" in the title.   

[nor-cal yota]

I guess I will add mine to the mix.

[Zs Confederate Toy]

These are great! I cant wait to get mine. Just gotta finish savin up

[Wermz84]

2WD?

Not that Minimal! 

[BigMike]

[GM]

Those are some clean looking set ups......Nice thread

[Cobbtunedsti]

Here's mine..

[BigMike]

Awesome! Love the center console

[*** YELLER ***]

ok I'll play