mud and oil dont work

Started by 79coyotefrg, February 17, 2004, 07:45:43 AM

0 Members and 2 Guests are viewing this topic.

Print
Go Down Pages1
User actions

79coyotefrg

February 17, 2004, 07:45:43 AM
well i fried the 20r with a little help from that tank trap,   blew the reAR MAIN apparently mud got into the pan

so now im installing a 22r block
gee i miss you guys

be back soon i hope
AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/    32/36weber, :driving: Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears    RIP Nitro 9-29-07 :(  I sure miss him :down: MarlinCrawlerInc IS NOT affiliated with TrailGear in any way

gferris5

#1
February 17, 2004, 11:45:37 AM
Well Glen, I'd suggest this  :rivers: plus this  :beer: and soon you'll be doing this :driving: If you lived any closer, I'd throw in some wrench time to make the time go faster...I also have 22r block if you need it, although shipping would be beyond ridiculous. Good luck.
85' 4Runner- SWAPPED--Dodge Caravan IFS-front and rear, 235R13's on each corner, hubcaps. Toyota Corona drivetrain swap. Locked, left and right side doors, with the windows up.

brainlessfool

#2
February 17, 2004, 07:34:52 PM
hummmmm, time for a 4.3 swap???
A good day working, that's just sick :reg:

95TacoTruck

#3
February 17, 2004, 08:00:25 PM
I didn't know you were leaving where did ya go man?
95 Tacoma Extra cab, many mods to come........

Marlin

#4
February 17, 2004, 08:09:40 PM
Make sure it is a 81-84' "tall block" so the timing chain will fit properly. :_order:

MC
1980 Toyota - 1997 3RZ-FE 2.7l Engine, Turbo R151F 4.31:1, Triple Turbo Marlin Crawler Billet (2.28x4.70x4.70) = 1,148:1 Crawl Ratio, Marlin Crawler Twin Stick and Short Throw Shift Kits, 30mm H/D Output Shaft, High Angle Drive Lines, 5.29:1, ARBs, High Pinion Front, 25mm HD Billet High Steer Kit, 6 Pin Locking Hub Bodies, 86+ Wide Rear End, V6 3rd member, Chromolly Axles all around, 37" IROKs with Beadlocks, York onboard air - Rollbar air tank, Premier Power Welder, Marlin Crawler 4" USA-made Leaf Springs, Bilstein Shocks, et cetera....

84runner

#5
February 17, 2004, 10:33:56 PM
Hey Glen didn't know you where gone.






But I guess we missed ya
RUBICON TESTED BIG BALLS APPROVED

79coyotefrg

#6
April 05, 2004, 06:32:53 AM
hey guys, i'm at the hospital in good old Hotsprings,  dont worry i aint dead yet :smack:hey i got my 22 tall block installed,  hey head bolts arent good after 3 or 4 times, mine were stretched almost a 1/4 inch, also if using stock 22 pistons with that  ring type dome,  you gotta cut some valve releifs if using a tall cam,  thank god my head bolts were bad or i'd a been buying valves,    well gotta run
next thing to do this weekend is install the 84 front axle i picked up

see you guys soon,   i'll be back online next week i think

oh hey i got some good pics of my mack dump truck radiator deep in mud
and my buddys truck tits up


see ya laters
AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/    32/36weber, :driving: Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears    RIP Nitro 9-29-07 :(  I sure miss him :down: MarlinCrawlerInc IS NOT affiliated with TrailGear in any way

gferris5

#7
April 05, 2004, 03:06:31 PM
good to hear it, Glen, hope whatever put you in the hospital lets you leave soon!
85' 4Runner- SWAPPED--Dodge Caravan IFS-front and rear, 235R13's on each corner, hubcaps. Toyota Corona drivetrain swap. Locked, left and right side doors, with the windows up.

brainlessfool

#8
April 05, 2004, 07:43:41 PM
 :psss:looking forward to "seeing you" back on the borad :biggthumpup:
A good day working, that's just sick :reg:

84runner

#9
April 05, 2004, 10:20:54 PM
Ya hope everything is alright, Dont leave us hangin like that Glen  :slap:
RUBICON TESTED BIG BALLS APPROVED

brainlessfool

#10
April 07, 2004, 08:08:53 PM
hope its not for a sex change op. :smack: don't think I could get use to Glenena on the borad. :hahaha:
A good day working, that's just sick :reg:

WHITE_TRASH

#11
April 08, 2004, 12:35:42 AM
damnit brainless I almost lost a mouthfull of Mt dew out the nose reading that!!!!
Full hydro, 186:1 with an auto and 44's what could go wrong??

brainlessfool

#12
April 08, 2004, 10:17:57 AM
anther point for the laugh? :teeth:
A good day working, that's just sick :reg:

84runner

#13
April 12, 2004, 11:38:25 PM
You got to hook him up for that one WT
RUBICON TESTED BIG BALLS APPROVED

mr4x42u

#14
April 15, 2004, 12:56:21 AM
hey glen you need to find some time here soon...alot of the (calander pics) have gone and i think its time we build the page up again.. :eyebrow:
Forgiveness is between them and god..
Its my job to arrange the meeting!

kyle_22r

#15
April 18, 2004, 06:14:26 PM
man, i didn't know it was possible to kill a 20R :smack:

79coyotefrg

#16
April 21, 2004, 10:02:04 AM
Quote from: brainlessfool on April 07, 2004, 08:08:53 PM
hope its not for a sex change op. :smack: don't think I could get use to Glenena on the borad. :hahaha:
:smack: :smack:nope, just let my blood sugar get a little out of control, :ack:i think Glenda is a better choice :hammer:
AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/    32/36weber, :driving: Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears    RIP Nitro 9-29-07 :(  I sure miss him :down: MarlinCrawlerInc IS NOT affiliated with TrailGear in any way

brainlessfool

#17
April 21, 2004, 01:00:33 PM
glad your back Glen, was getting boring here with out you! :psss:  I was looking forward to meeting Glenena  thou :smack:
A good day working, that's just sick :reg:
Print
Go Up Pages1
User actions