Author Topic: My new running gear (Read 82818 times)

alwayzbroken · « **Reply #240 on:** Jan 06, 2007, 03:43:18 PM »

How much width did you gain over the old toy axles? You cut the drivers side down 2" correct? Do you have a front shot of the truck from a ways back?

What pitman arm did you have modified? I assume it was the old toyota hysteer pitman arm. I am guessing WFO did that also.

toybuilt · « **Reply #241 on:** Jan 09, 2007, 10:27:17 PM »

Quote from: alwayzbroken on Jan 06, 2007, 03:43:18 PM

How much width did you gain over the old toy axles? You cut the drivers side down 2" correct? Do you have a front shot of the truck from a ways back?

What pitman arm did you have modified? I assume it was the old toyota hysteer pitman arm. I am guessing WFO did that also.

I don't have to many good pictures from the front, heres what I have. The pitman arm is stock, no extra bends in it. I gained about 4" or 5" of width, it could have been more but I have a 5" offset on my wheels. The driver side was cut about 2.5"

gotrocks · « **Reply #242 on:** Jan 10, 2007, 12:02:02 AM »

looking really really good man. I am really excited to see his done. Its coming out very nice

crawlerdan · « **Reply #243 on:** Jan 10, 2007, 08:31:33 AM »

id like to tell everyone that i personally whitnessed his truck do a FRONT WHEEL DRIVE burnout into the first three gears yesterday....he flung poo on my arms!!! it wqas baddass

the only bad thing is that it is sooooooooooo hot in that truck because of the HUGE hole in what used to be a floor.....on th ebright side, you can watch the axle move, and the steering, and the motor, and the tranny...and the........

gotrocks · « **Reply #244 on:** Jan 10, 2007, 11:42:18 AM »

hahaha. Did it do the burnout because it doesn't have the rear driveline. If not I didn't know that you could get a rear diconnect for the 205

crawlerdan · « **Reply #245 on:** Jan 10, 2007, 04:27:26 PM »

rear diconnect

gotrocks · « **Reply #246 on:** Jan 11, 2007, 07:08:10 PM »

thats $That\'s Gay$ why would you want rear disconnect. Front digs are way over rated. I'd never put one in my rig

toybuilt · « **Reply #247 on:** Jan 12, 2007, 12:27:25 PM »

I have front wheel disconect on my np205. Dan we went though all 4 gears in FWD low.

Some bad news for today though, my clutch went out

I believe the throw out bearing was on the precher plate all the time and caused it to blow

So I have a center force clutch on it way.

toybuilt · « **Reply #248 on:** Jan 12, 2007, 12:28:50 PM »

I have front wheel disconect on my np205. Dan we went though all 4 gears in FWD low. It was about a 20 foot burnout

Some bad news for today though, my clutch went out

I believe the throw out bearing was on the precher plate all the time and caused it to blow

So I have a center force clutch on it way.

gotrocks · « **Reply #249 on:** Jan 12, 2007, 06:20:30 PM »

Quote from: toybuilt on Jan 12, 2007, 12:28:50 PM

I have front wheel disconect on my np205.

we all have front wheel disconnect I think you mean rear disconnect

DTB · « **Reply #250 on:** Jan 12, 2007, 06:32:35 PM »

Quote from: gotrocks on Jan 12, 2007, 06:20:30 PM

we all have front wheel disconnect I think you mean rear disconnect

toybuilt · « **Reply #251 on:** Jan 12, 2007, 11:31:55 PM »

Quote from: gotrocks on Jan 12, 2007, 06:20:30 PM

we all have front wheel disconnect I think you mean rear disconnect

The way I see it is that the FWD gears are being seperated from the RWD gears, plus thats what all the shops call it around here.

toybuilt · « **Reply #252 on:** Jan 21, 2007, 05:20:50 PM »

Well my truck is parked until I rebuild my np465, since something broke on the inside. I'm guessin it was a gear, it makes some really bad grinding noises. Also my clutch went out as well, already ordered and received my new Center Force. It's sittin in my garage.

crawlerdan · « **Reply #253 on:** Jan 21, 2007, 06:27:29 PM »

toybuilt · « **Reply #254 on:** Jan 23, 2007, 08:46:05 AM »

Quote from: crawlerdan on Jan 21, 2007, 06:27:29 PM

FART

6.72:1 · « **Reply #255 on:** Jan 28, 2007, 01:12:55 AM »

Quote from: toybuilt on Jan 21, 2007, 05:20:50 PM

Well my truck is parked until I rebuild my np465, since something broke on the inside. I'm guessin it was a gear, it makes some really bad grinding noises. Also my clutch went out as well, already ordered and received my new Center Force. It's sittin in my garage.

Well, I'll be dipped. Don't lose motivation though!

toybuilt · « **Reply #256 on:** Jan 28, 2007, 08:47:52 AM »

The shop I go to has a guy that will rebuilt it for about $400 maybe less

So all be doin that in a little bit, as soon as I pay off a few things.

toybuilt · « **Reply #257 on:** Feb 04, 2007, 10:23:26 AM »

Well my truck is fixed, it drives again. Only thing is I didn't mess with anything

I did see however that all this time I've been drivin in my low range with the klune V

at least it didn't heart anything and its not even that much faster

crawlerdan · « **Reply #258 on:** Feb 04, 2007, 10:50:44 AM »

hahahaha...weirdo

6.72:1 · « **Reply #259 on:** Feb 04, 2007, 03:53:22 PM »

Haha...nothing like underdriving it everywhere!

alwayzbroken · « **Reply #260 on:** Feb 04, 2007, 04:10:47 PM »

When are you gonna have it out on the trail? I wanna hear how it works.

toybuilt · « **Reply #261 on:** Feb 06, 2007, 05:43:10 PM »

Quote from: alwayzbroken on Feb 04, 2007, 04:10:47 PM

When are you gonna have it out on the trail? I wanna hear how it works.

I've been brakin the engine in and makin sure everything is workin right. I am weedin out wires from the toyota wire harness so I can have headlights and wipperes. I still need to make bump stops for the front so my oilpan and tierod welln't smack each other. I'm just don't know where I want them yet. I need to do make some kind of vent on the hood to let all the hot air from the engine out. Also I still need to make a tranny tunnel as well. Pretty much I've just been driven my truck and not workin on it, I've been slackin.

alwayzbroken · « **Reply #262 on:** Feb 06, 2007, 08:34:37 PM »

Quote from: toybuilt on Feb 06, 2007, 05:43:10 PM

I need to do make some kind of vent on the hood to let all the hot air from the engine out.

You could try mounting a cheap electric fan under the hood on push blowing the hot air out through some speed holes drilled in the hood. I think holes would look better than some big gay scoop or something.

crawlerdan · « **Reply #263 on:** Feb 07, 2007, 07:19:53 AM »

vents al la crawlerdan!

toybuilt · « **Reply #264 on:** Mar 11, 2007, 05:57:16 PM »

Well its been a while, haven't really been workin on my truck much. I did start my transmission tunel today. Also I have ripped out all of my dash, I didn't need it anyways. The bad thing is I have to smog it by the end of this month or else I only get one day moving perments from the DMV, I really dislike DMV

crawlerdan · « **Reply #265 on:** Mar 11, 2007, 06:05:35 PM »

holy no dashboard batman!!!!...tranny tunnel looks good though

toybuilt · « **Reply #266 on:** Mar 13, 2007, 02:13:56 PM »

Hears a pic of the other side of the tranny tunnel. Also got a speedo gage and fuel gage. The weathers been really nice, about 80 degrees, hear so I took the doors back off and have been driving around town, slow and fast. My truck's temp never got over 180 degrees so I feel good about that, but once I start to crawl and work it hard it goes over 200. So I have some fans that I took off my old Dodge and I'm going to put at least one of them on the Toy-vie. Also have some louvers from a New Yorker that where on my old Dodge that will be going on the Toy-vie as well.

toybuilt · « **Reply #267 on:** Mar 15, 2007, 01:37:00 PM »

I desided to move my tierod to the front of the axle for now, which ment I have to lenthin it about 3 inches. I did it because I'm still not sure how I want to built the bump stops in the front so the tierod and oilpan welln't smack each other when the frontend hops. I used 1.5" ID shedule 80 that I have layin around the house, it works for now.

crawlerdan · « **Reply #268 on:** Mar 15, 2007, 01:58:05 PM »

looks good buddy, drag link in the same place still??

toybuilt · « **Reply #269 on:** Aug 01, 2007, 09:22:11 PM »

Ok well its been a while since I've work on my truck. But all that is about to change since MCR6 is almost here.

Heres what I need to do:

1-Finish a few smog details
2-Smog my truck
3-Rock lights
4-Finish putting my gages in
5-Put another fuse panel in
6-Posably a second fan for the radiator
7-Cut a few holes in the roof to let the engine breath bether
8-Finish the tranny tunnel(this one's for you Dan)
9-Everything else I forgot!

toybuilt [OP]

toybuilt [OP]

toybuilt [OP]

toybuilt [OP]

toybuilt [OP]

toybuilt [OP]

toybuilt [OP]

toybuilt [OP]

toybuilt [OP]

toybuilt [OP]

toybuilt [OP]

toybuilt [OP]

toybuilt [OP]

Related Topics