Author Topic: Tell me your tricks... (Read 3467 times)

Rockhoppa · « **on:** Feb 16, 2005, 10:40:10 PM »

I just got a v6 rearend, but the filler plug is striped round. What would you do?

BigMike · « **Reply #1 on:** Feb 16, 2005, 10:41:00 PM »

Retap it? Weld it shut and replace the two lower studs with bolts; pull the bolts to drain.

oddball · « **Reply #2 on:** Feb 16, 2005, 10:50:33 PM »

IVE HAD LUCK WITH A CHISEL AND MALLET. JUT A COUPLE OF TAPS ON THE SIDE OF THE PLUG AND IT SHOULD LOSEN UP

BigMike · « **Reply #3 on:** Feb 16, 2005, 11:14:43 PM »

OH the hex pattern is stripped, I read it wrong and thought it was the treads. Yes, just use a hammer and a chisel and try to hit the chisel near the radius of the bolt so you can get the most amount of tangential torque to loosen it up and pull it out!

BLACKDOG · « **Reply #4 on:** Feb 17, 2005, 12:57:14 AM »

Quote from: BigMike on Feb 16, 2005, 11:14:43 PM

of tangential torque to loosen it up and pull it out!

Little words mike, little words for all us numbskulls

trollbum · « **Reply #5 on:** Feb 17, 2005, 02:22:08 AM »

i know its hokey but would welding a bar onto the head save you some time, read it somewhere else

FATB0Y · « **Reply #6 on:** Feb 17, 2005, 03:21:44 AM »

Quote from: blackdog on Feb 17, 2005, 12:57:14 AM

Little words mike, little words for all us numbskulls

but true

Rockhoppa · « **Reply #7 on:** Feb 17, 2005, 07:57:19 AM »

Thanks for the replys, already tryed the chisel and hammer, already tryed penitrating lube, already tried heating it up, already tried vice-grips and a BFH. I was thinking of welding another nut to it and than trying to break it loose, Ill try tonight when I get home. Anything else I should try first though?

mr4x42u · « **Reply #8 on:** Feb 17, 2005, 08:02:41 AM »

leave it in and pull the bottom studs out of the thirdmermber..It will drain that way.Just a little bit slower..

reklund5 · « **Reply #9 on:** Feb 17, 2005, 08:37:54 AM »

I use a chisel tip in my air hammer at work all the time....Its a little overkill but always pops 'em loose. Welding a nut to it will work too...

Ryan

ntsqd · « **Reply #10 on:** Feb 17, 2005, 02:21:14 PM »

Try using a coupler nut if you can find one close to the right size. They're longer so your weld bead won't reduce the wrench area. Have the wrench handy and try while still hot from welding.

mplatzer · « **Reply #11 on:** Feb 17, 2005, 02:40:09 PM »

go with welding a nut on the plug and make sure that it is a big one so you can get good leverage with a wrench

WileEToyote · « **Reply #12 on:** Feb 17, 2005, 03:54:00 PM »

Or just weld the socket to what's left of the plug. Then, provided it was Craftsman, grind it off and take it back to Sears for a replacement

freds40 · « **Reply #13 on:** Feb 17, 2005, 05:07:05 PM »

I usually weld a nut on in these situations. For that one I'd use like a nut for a 3/4" bolt. Plenty of meat to weld on and plenty of surface area to grab with a wrench. When welding, set your ground clamp to the nut to lessen the chance of arcing from the plug to the threads and tacking them together. This could really mess up your threads when you back the plug out.

79coyotefrg · « **Reply #14 on:** Feb 17, 2005, 05:32:51 PM »

Quote from: mr4x42u on Feb 17, 2005, 08:02:41 AM

leave it in and pull the bottom studs out of the thirdmermber..It will drain that way.Just a little bit slower..

me >

< mr4x4 hes trying to ADD lube not drain it

kneedownnate · « **Reply #15 on:** Feb 17, 2005, 05:42:53 PM »

Quote from: blackdog on Feb 17, 2005, 12:57:14 AM

Little words mike, little words for all us numbskulls

No no no, big words please!! Make us think, and in my case atleast, try and make up for what watching too much tv all my life has done to my brain! I may have been born in Missouri and grown up in the sticks but nobody really needs to know now do they? Nate

79coyotefrg · « **Reply #16 on:** Feb 17, 2005, 05:56:55 PM »

Quote from: kneedownnate on Feb 17, 2005, 05:42:53 PM

No no no, big words please!! Make us think, and in my case atleast, try and make up for what watching too much tv all my life has done to my brain! I may have been born in Missouri and grown up in the sticks but nobody really needs to know now do they? Nate

your in missouri

Rockhoppa · « **Reply #17 on:** Feb 17, 2005, 08:24:20 PM »

Well I ended up welding a nut to it, Came off with no problem.

Fireimp141 · « **Reply #18 on:** Feb 17, 2005, 09:17:41 PM »

Gj skipper

MidgetMike · « **Reply #19 on:** Feb 17, 2005, 11:11:36 PM »

you can drill a hole in it and use an easy out but just weld a 1/2 foot long piece of 1/4 " rod side ways to it like a wrench handle and un screw it

Rockhoppa [OP]

- Sales Employee -

Rockhoppa [OP]

Related Topics