Author Topic: Issue getting into gear (Read 1442 times)

Jedi87 · « **on:** Dec 09, 2006, 05:12:59 PM »

I replaced my w56 with one of Marlins hd units, a Centerforce dual friction clutch, pilot bearing and throwout. I have noticed that it is hard to get into gear when running, it goes in but with a little work. It goes through the gears easy when it isn't running and the clutch is in. If I have it running and try to put it in gear and it's not going in, I can shut it off while still applying a little pressure on the shifter and once I turn it off it slides right into gear.

79coyotefrg · « **Reply #1 on:** Dec 09, 2006, 05:25:43 PM »

adjust your clutch its not releasing completely

boggerunner · « **Reply #2 on:** Dec 09, 2006, 05:27:06 PM »

yep, bleed the clutch, or check if the clutch is working properly

Wermz84 · « **Reply #3 on:** Dec 09, 2006, 05:30:31 PM »

x3, when was the last time you bled the fluid through? I would also just double check that the slave cylinder is functioning properly.

Jedi87 · « **Reply #4 on:** Dec 09, 2006, 05:36:44 PM »

I bled it a couple months ago when i replaced the master/slave cylinders. I will rebleed tomorrow and see if it helps. Everything from the motor to the axles are new, I mean everything so it shouldn't be anything big.

Stinky · « **Reply #5 on:** Dec 27, 2006, 08:37:17 AM »

piss with the adjuster on the pedal...loosen up the jam nut, thread it out a lil n tighten the jam nut back down...

Author Topic: Issue getting into gear (Read 1442 times)

Jedi87

Issue getting into gear

79coyotefrg

Re: Issue getting into gear

boggerunner

Re: Issue getting into gear

Wermz84

Re: Issue getting into gear

Jedi87 [OP]

Re: Issue getting into gear

Stinky

Re: Issue getting into gear

Related Topics


	Author Topic: Issue getting into gear (Read 1442 times) 0 Members and 1 Guest are viewing this topic. Jedi87 Rock Crawl'n Turtle Points: 0 Posts: 14 Member since Jul '06 Issue getting into gear « on: Dec 09, 2006, 05:12:59 PM » I replaced my w56 with one of Marlins hd units, a Centerforce dual friction clutch, pilot bearing and throwout. I have noticed that it is hard to get into gear when running, it goes in but with a little work. It goes through the gears easy when it isn't running and the clutch is in. If I have it running and try to put it in gear and it's not going in, I can shut it off while still applying a little pressure on the shifter and once I turn it off it slides right into gear. Logged 87 4runner 22re bored .030,Kieth Black pistons,stage II "272" cam ,oversized valves,New amc head,ARP studs,electric fan,Doug Thorley header, 2 1/4 flowmaster cat back,5 speed,3 inch body lift,33 inch bfg m/t's.Centerforce dual friction clutch,Marlin Crawler hd-w56,Yukon 4.88's 99 4runner SR5 v6 automatic 4x4 79coyotefrg Rock Ninja Gold Turtle Award Turtle Points: 1452 Posts: 22,633 Member since May '02 Solid axle Toys Rule ! ! ! Re: Issue getting into gear « Reply #1 on: Dec 09, 2006, 05:25:43 PM » adjust your clutch its not releasing completely Logged AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/ 32/36weber, Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears RIP Nitro 9-29-07 I sure miss him $I\'m Down$ MarlinCrawlerInc IS NOT affiliated with TrailGear in any way boggerunner Silver Turtle Award Turtle Points: 9 Posts: 3,140 Member since May '06 Philberbuilt Re: Issue getting into gear « Reply #2 on: Dec 09, 2006, 05:27:06 PM » yep, bleed the clutch, or check if the clutch is working properly Logged Wermz84 Rock Nerd! Silver Turtle Award Turtle Points: 921 Posts: 3,518 Member since May '05 Ouch My Eye! Re: Issue getting into gear « Reply #3 on: Dec 09, 2006, 05:30:31 PM » x3, when was the last time you bled the fluid through? I would also just double check that the slave cylinder is functioning properly. Logged I like to Drive! Jedi87 [OP] Rock Crawl'n Turtle Points: 0 Posts: 14 Member since Jul '06 Re: Issue getting into gear « Reply #4 on: Dec 09, 2006, 05:36:44 PM » I bled it a couple months ago when i replaced the master/slave cylinders. I will rebleed tomorrow and see if it helps. Everything from the motor to the axles are new, I mean everything so it shouldn't be anything big. Logged 87 4runner 22re bored .030,Kieth Black pistons,stage II "272" cam ,oversized valves,New amc head,ARP studs,electric fan,Doug Thorley header, 2 1/4 flowmaster cat back,5 speed,3 inch body lift,33 inch bfg m/t's.Centerforce dual friction clutch,Marlin Crawler hd-w56,Yukon 4.88's 99 4runner SR5 v6 automatic 4x4 Stinky Crawler Guru Turtle Points: 8 Posts: 636 Member since Aug '05 my wifes vagine, it hangs like a sleeve of wizard Re: Issue getting into gear « Reply #5 on: Dec 27, 2006, 08:37:17 AM » piss with the adjuster on the pedal...loosen up the jam nut, thread it out a lil n tighten the jam nut back down... Logged 87 p/u SAS, 22RE, built, then cut up and scrapped 94 ex cab P/U, SR5, fully loaded, 3.4 swap, r150f, a/c, bumpers, 33s, glass fenders...sold 00 Stoopid Duty 250, ex cab, lariat, v-10,000 94 reg cab, 22re, duals, 38.5 boggers, sas, 4 link, tube bed, build underway... http://pirate4x4.com/forum/showthread.php?t=967836 88 Samurai, soa, buick 3.8, th350, zuki case, 1/4 done... anyone wanna buy it??