Author Topic: SA (Read 994 times)

builttoabuse · « **on:** Aug 15, 2011, 09:01:33 AM »

Im planning on picking up a SA for my truck but i dont know a whole lot about what i should be looking for to make sure its a good axle besides to check if its bent. im paying 300.00. Any advice would be useful thanks

dirtybird · « **Reply #1 on:** Aug 15, 2011, 08:42:37 PM »

I would say looking for bent is a good start. And if you are planing on just installing it or going through it. If you're going to go through it just make sure it isn't bent or missing parts. If you plan on just installing it better make sure bearings are good no play in knuckles or oil leaking out everywhere not to beat up brakes and rotors in decent condition etc etc

dirtybird · « **Reply #2 on:** Aug 15, 2011, 08:44:26 PM »

Also check hubs lock and unlock and that they actually turn the pinion flange when in locked position letting you know that it hasn't been gutted and there is axles inside!!! Hope this helps. Where you located?

Peterbuilt84 · « **Reply #3 on:** Aug 15, 2011, 09:00:13 PM »

It's kind of hard to tell what shape the axle is in without taking it all apart. Obvious things would be to check if it's bent, do the hubs lock and unlock, and in anything broken. Check out this link, tons of good info.

http://www.pirate4x4.com/forum/showthread.php?t=775780

builttoabuse · « **Reply #4 on:** Aug 15, 2011, 10:14:05 PM »

thank you alot everyone this info will be useful and I am located in Dana Point,CA

Author Topic: SA (Read 994 times)

builttoabuse

SA

dirtybird

Re: SA

dirtybird

Re: SA

Peterbuilt84

Re: SA

builttoabuse [OP]

Re: SA


	Author Topic: SA (Read 994 times) 0 Members and 1 Guest are viewing this topic. builttoabuse Crawler Guru Turtle Points: -33 Posts: 498 Member since Aug '11 toy obsessed SA « on: Aug 15, 2011, 09:01:33 AM » Im planning on picking up a SA for my truck but i dont know a whole lot about what i should be looking for to make sure its a good axle besides to check if its bent. im paying 300.00. Any advice would be useful thanks Logged toy obsessed! dirtybird Rock Master Turtle Points: 3 Posts: 166 Member since Aug '11 Re: SA « Reply #1 on: Aug 15, 2011, 08:42:37 PM » I would say looking for bent is a good start. And if you are planing on just installing it or going through it. If you're going to go through it just make sure it isn't bent or missing parts. If you plan on just installing it better make sure bearings are good no play in knuckles or oil leaking out everywhere not to beat up brakes and rotors in decent condition etc etc Logged dirtybird Rock Master Turtle Points: 3 Posts: 166 Member since Aug '11 Re: SA « Reply #2 on: Aug 15, 2011, 08:44:26 PM » Also check hubs lock and unlock and that they actually turn the pinion flange when in locked position letting you know that it hasn't been gutted and there is axles inside!!! Hope this helps. Where you located? Logged Peterbuilt84 The 1K Club Turtle Points: 12 Posts: 1,049 Member since Sep '09 Re: SA « Reply #3 on: Aug 15, 2011, 09:00:13 PM » It's kind of hard to tell what shape the axle is in without taking it all apart. Obvious things would be to check if it's bent, do the hubs lock and unlock, and in anything broken. Check out this link, tons of good info. http://www.pirate4x4.com/forum/showthread.php?t=775780 Logged My Build: http://board.marlincrawler.com/index.php?topic=71999 builttoabuse [OP] Crawler Guru Turtle Points: -33 Posts: 498 Member since Aug '11 toy obsessed Re: SA « Reply #4 on: Aug 15, 2011, 10:14:05 PM » thank you alot everyone this info will be useful and I am located in Dana Point,CA Logged toy obsessed!