Author Topic: Front Bumpers and Cab Cages!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! (Read 52354 times)

BigMike · « **Reply #90 on:** Jun 01, 2007, 12:39:40 PM »

Ok, here is another version of the stinger supports, which are shorter and now I actually do like this look better than the straight ones.

This bumper also has an optional front receiver mount.

Quote from: rlwjaw on May 31, 2007, 08:55:58 PM

doesnt look like it will accept a roller fairlead.

This is correct, and our old bumper also only accepts a hawse fairlead.

Here are some close ups of the new 10-point bolt locations (only one side shown for detail).

A couple more upgrades have been done to these prototypes including a couple more triangle brackets for added strength.

Talon84x4 · « **Reply #91 on:** Jun 01, 2007, 12:51:23 PM »

I like the shorter bar look than the longer

Looks sweet

*ROKTOY* · « **Reply #92 on:** Jun 01, 2007, 02:17:17 PM »

Still like the single bend stinger with straight supports. The ten bolts look good, but I think it still needs more support higher behind the winch plate.

82toycrawler · « **Reply #93 on:** Jun 01, 2007, 09:05:39 PM »

Does look a little better, still like the old stinger better.

The mounts look nice, should work well.

twistedtoy92 · « **Reply #94 on:** Jun 02, 2007, 12:35:21 AM »

looks sweet... might like the old stinger better though!

cheap sunglasses · « **Reply #95 on:** Jun 02, 2007, 02:54:21 PM »

x5 (or whatever) for the old stinger looking best. Between the two new ones the shorter supports look better.

unclejpl4x4 · « **Reply #96 on:** Jun 02, 2007, 03:41:27 PM »

rlwjaw · « **Reply #97 on:** Jun 02, 2007, 04:18:15 PM »

.
This is correct, and our old bumper also only accepts a hawse fairlead.

I was told on the phone that they would accept a roller fairlead. Can they be made to accept one?

havik · « **Reply #98 on:** Jun 05, 2007, 09:39:43 AM »

iam not diggin the bent supports. maybe if they came out more to protect the grill corners and headlights but where they are they dint seem to serve enough purpose. i think straight would be better.

www.fullsize4wd.com · « **Reply #99 on:** Jun 17, 2007, 10:44:47 AM »

Any plan to offer a version that supports body lifts? Mainly a 1" but still keep really close to the grill and fenders.

TurtleTappers91 · « **Reply #100 on:** Jun 17, 2007, 11:50:28 AM »

Damn, still no cab cages?

looks like I'm buying it from All Pro...

guywithuglyyota · « **Reply #101 on:** Jun 17, 2007, 10:26:19 PM »

Quote from: TurtleTappers91 on Jun 17, 2007, 11:50:28 AM

Damn, still no cab cages?
looks like I'm buying it from All Pro...

BUT I WANT A GOLDEN GOOSE NOWWWW!!!!!

CruzrDave · « **Reply #102 on:** Jun 18, 2007, 10:54:14 AM »

Quote from: rlwjaw on Jun 02, 2007, 04:18:15 PM

.
This is correct, and our old bumper also only accepts a hawse fairlead.

I was told on the phone that they would accept a roller fairlead. Can they be made to accept one?

We tried to keep everything tucked up tight. The roller fair lead sticks out farther and does not usually survive a rock beating to well.

Quote from: www.fullsize4wd.com on Jun 17, 2007, 10:44:47 AM

Any plan to offer a version that supports body lifts? Mainly a 1" but still keep really close to the grill and fenders.

We have tried to maintain 1/2" of tube clearance around the head light bezel. How ever we have noticed that not one truck is the same. There is a large amount of tolerance in the Toyota bracketry for the stock bumper. We have had to maintain some tolerance. We have different tube length for different years so we could possibly build you a 1" taller bumper but that would be the maximum. We have also stacked an extra 1-3/4" main tube to help hide the gap on a 2" body lift truck. These are possible options we could do. Because we do not farm these out to 3rd world counties we can offer some customizing.

We have will be using the straight support tubes for the hoop. We have also finished the 1984-1985 brackets and an extra support gusset that we be used on all the front bumpers.

Quote from: TurtleTappers91 on Jun 17, 2007, 11:50:28 AM

Damn, still no cab cages?
looks like I'm buying it from All Pro...

We had to put the Cage kits on the back burn the last few weeks to finish the front bumper designs and brackets. We are back on the cage design and I hope to have a finished sample by the end of the this week. Oh, did I mention that we plan to sell them for $299!

unclejpl4x4 · « **Reply #103 on:** Jun 18, 2007, 01:01:47 PM »

So when will the bumpers go on mass produce I real would like one.

Fearofrunner · « **Reply #104 on:** Jun 18, 2007, 02:48:04 PM »

so are you guys going to stay with the rounded front supports? Because i have to agree with these guys the shape just isn't as appealing to me.

unclejpl4x4 · « **Reply #105 on:** Jun 18, 2007, 03:31:23 PM »

i like it

i also like the reciver perfice place for my cargo rack/cooler

Talon84x4 · « **Reply #106 on:** Jun 18, 2007, 10:23:29 PM »

Quote from: CruzrDave on Jun 18, 2007, 10:54:14 AM

We have will be using the straight support tubes for the hoop. We have also finished the 1984-1985 brackets and an extra support gusset that we be used on all the front bumpers.

*ROKTOY* · « **Reply #107 on:** Jun 19, 2007, 05:32:15 AM »

Quote from: Talon84x4 on Jun 18, 2007, 10:23:29 PM

What about the hoop it self?

TurtleTappers91 · « **Reply #108 on:** Jun 19, 2007, 05:59:21 PM »

Quote from: CruzrDave on Jun 18, 2007, 10:54:14 AM

We had to put the Cage kits on the back burn the last few weeks to finish the front bumper designs and brackets. We are back on the cage design and I hope to have a finished sample by the end of the this week. Oh, did I mention that we plan to sell them for $299!

$100 bucks cheaper than the AllPro cage? It is worth waiting for a while I guess, I will gladly pay $299. I know you don't like giving ETA's , but I don't want to wait 6+ months like I did with the front bumper....How long after you guys approve the sample or whatever, is it going to take? be realistic please.

Wermz84 · « **Reply #109 on:** Jun 20, 2007, 09:49:03 AM »

Quote from: CruzrDave on Jun 18, 2007, 10:54:14 AM

We had to put the Cage kits on the back burn the last few weeks to finish the front bumper designs and brackets. We are back on the cage design and I hope to have a finished sample by the end of the this week. Oh, did I mention that we plan to sell them for $299!

That is an awsome price.

but some of are waiting on the word for an X-tra cab option.

Rockcrawlintoy · « **Reply #110 on:** Jun 20, 2007, 10:26:26 AM »

Quote from: CruzrDave on Jun 18, 2007, 10:54:14 AM

We had to put the Cage kits on the back burn the last few weeks to finish the front bumper designs and brackets. We are back on the cage design and I hope to have a finished sample by the end of the this week. Oh, did I mention that we plan to sell them for $299!

sweet thats what i am talkin about.

BLACKDOG · « **Reply #111 on:** Jun 20, 2007, 03:01:53 PM »

Quote from: Wermz84 on Jun 20, 2007, 09:49:03 AM

That is an awsome price. but some of are waiting on the word for an X-tra cab option.

some people have big plans hinging on this cage

3rd gen xcab

*ROKTOY* · « **Reply #112 on:** Jun 23, 2007, 08:54:29 AM »

Quote from: toyguy86 on Jun 19, 2007, 05:32:15 AM

What about the hoop it self?

Talon84x4 · « **Reply #113 on:** Jun 24, 2007, 02:24:24 PM »

Could we get just a bumper without stinger?

Like this?

cheap sunglasses · « **Reply #114 on:** Jun 26, 2007, 12:30:54 AM »

Quote from: Talon84x4 on Jun 24, 2007, 02:24:24 PM

Could we get just a bumper without stinger?

Pretty sure the stinger has always been an added option.

BLACKDOG · « **Reply #115 on:** Jun 26, 2007, 12:34:35 AM »

Quote from: Talon84x4 on Jun 24, 2007, 02:24:24 PM

Could we get just a bumper without stinger?

Like this?

the stinger is a $75 option

Talon84x4 · « **Reply #116 on:** Jun 26, 2007, 11:21:49 AM »

Sweet, thanks

, i'll let my buddy know

Aaron84x4 · « **Reply #117 on:** Jun 26, 2007, 04:02:21 PM »

so.....any word on the roll cages yet?

I'm dyin to see the new design, especially for that awsome new price!

rlwjaw · « **Reply #118 on:** Jun 27, 2007, 09:00:00 AM »

Do we have a shipping date on the bumpers yet?

havik · « **Reply #119 on:** Jun 28, 2007, 10:58:53 AM »

what about selling unwelded bumpers as a kit? how much would that cost?

CruzrDave [OP]

Related Topics