Author Topic: Diesel GOAT: The one I wish Toyota would have built  (Read 202249 times)

0 Members and 2 Guests are viewing this topic.

redneckcustoms13

  • Offline The 2.5K Group
  • ****
  • Turtle Points: 7674
  • Male Posts: 2,513
  • Member since May '15
    • View Profile
    • Buy me a beer
What pyro are you going to run?
83 long bed 2wd sas, 3rz, w56, duals with 4.7 rear, 4.88 elock front, spartan rear, 39.5 iroks
01 double cab hunting truck
06 tacoma street truck

helipilot77 [OP]

  • Offline The 1.5K Club
  • **
  • Turtle Points: 1018
  • Male Posts: 1,725
  • Member since Jul '12
  • Seattle, WA
    • View Profile
    • My build thread
What pyro are you going to run?

It’s a PLX I also have a vac/boost, AFR wideband, intake temp, oil pressure and coolant temp sending units that I’m feeding to the multigauge display unit.   
-1987 SR5 4runner, 1KZ-t turbo diesel with mech. pump
 & custom 3" S.S. dump pipe, R-151f transmission, marlin dual ultimate transfer cases w/ triple shifter, SAS, 35's https://board.marlincrawler.com/index.php?topic=98969.0
-1984 SR5 Tercel 4wd wagon bone stock - given to my nephew https://board.marlincrawler.com/index.php?topic=100547.0
-1:10 scale RC 4wd crawler w/yota axles, R2 2 speed enclosed dig tranny and 1st gen 4Runner body by BigBird
-My front axle service write-up http://board.marlincrawler.com/i

helipilot77 [OP]

  • Offline The 1.5K Club
  • **
  • Turtle Points: 1018
  • Male Posts: 1,725
  • Member since Jul '12
  • Seattle, WA
    • View Profile
    • My build thread
This weekend was spent cleaning and painting all the last of the engine parts so they can go on. I also had to Tig weld some mounting bosses  for the turbo heat shield to mount to. After breaking a tap I eventually got that done. At the end of the day on Sunday I bolted a few small parts onto the motor
« Last Edit: Jul 16, 2018, 07:50:27 AM by helipilot77 »
-1987 SR5 4runner, 1KZ-t turbo diesel with mech. pump
 & custom 3" S.S. dump pipe, R-151f transmission, marlin dual ultimate transfer cases w/ triple shifter, SAS, 35's https://board.marlincrawler.com/index.php?topic=98969.0
-1984 SR5 Tercel 4wd wagon bone stock - given to my nephew https://board.marlincrawler.com/index.php?topic=100547.0
-1:10 scale RC 4wd crawler w/yota axles, R2 2 speed enclosed dig tranny and 1st gen 4Runner body by BigBird
-My front axle service write-up http://board.marlincrawler.com/i

helipilot77 [OP]

  • Offline The 1.5K Club
  • **
  • Turtle Points: 1018
  • Male Posts: 1,725
  • Member since Jul '12
  • Seattle, WA
    • View Profile
    • My build thread
More progress. I got the injector pipes installed and also got that beautiful turbo installed last night.

-1987 SR5 4runner, 1KZ-t turbo diesel with mech. pump
 & custom 3" S.S. dump pipe, R-151f transmission, marlin dual ultimate transfer cases w/ triple shifter, SAS, 35's https://board.marlincrawler.com/index.php?topic=98969.0
-1984 SR5 Tercel 4wd wagon bone stock - given to my nephew https://board.marlincrawler.com/index.php?topic=100547.0
-1:10 scale RC 4wd crawler w/yota axles, R2 2 speed enclosed dig tranny and 1st gen 4Runner body by BigBird
-My front axle service write-up http://board.marlincrawler.com/i

helipilot77 [OP]

  • Offline The 1.5K Club
  • **
  • Turtle Points: 1018
  • Male Posts: 1,725
  • Member since Jul '12
  • Seattle, WA
    • View Profile
    • My build thread
The Turbo oil supply line had been giving me trouble it's in an impossible place to get to and I had screwed up the copper gasket and was waiting for the replacement to arrive. This week it showed-up and I promised myself to get it together this weekend if it was the only thing I did on my truck. I only had Sunday off work this weekend so I spent a couple hours working on it. I just couldn't get a wrench on the banjo bolt so I had to modify one. I also attached a picture of my shop which as you can see is massive. Anyways I finally got it bolted up.
« Last Edit: Aug 13, 2018, 08:07:29 AM by helipilot77 »
-1987 SR5 4runner, 1KZ-t turbo diesel with mech. pump
 & custom 3" S.S. dump pipe, R-151f transmission, marlin dual ultimate transfer cases w/ triple shifter, SAS, 35's https://board.marlincrawler.com/index.php?topic=98969.0
-1984 SR5 Tercel 4wd wagon bone stock - given to my nephew https://board.marlincrawler.com/index.php?topic=100547.0
-1:10 scale RC 4wd crawler w/yota axles, R2 2 speed enclosed dig tranny and 1st gen 4Runner body by BigBird
-My front axle service write-up http://board.marlincrawler.com/i

Prismo

  • Offline The 1K Club
  • *
  • Turtle Points: 8319
  • Posts: 1,275
  • Member since Oct '03
  • Living in the green house
    • View Profile
I work under a carport too. It can be a hassle at times. That engine looks factory new now. :thumbs:
Retired Great White Turtle Hunter
Originally posted by fortysixandtwo – sheesh, you should see the transvestites i sell ammo to sometimes

300k

  • Offline Crawler Guru
  • ****
  • Turtle Points: 3744
  • Male Posts: 623
  • Member since Jun '15
  • GREEN NAME MAN BAD!
    • View Profile
    • Please ban me!
          OK!
      I am banned!
I work on a concrete slab. About burned my fingers off holding onto a 19mm wrench too long :gap:. Your shop is nice, better than my excab turned storage shed :thumbs:
:)bestgen4runner [12:45 PM]:   I am so stupid.

Truer words have never been spoken...

helipilot77 [OP]

  • Offline The 1.5K Club
  • **
  • Turtle Points: 1018
  • Male Posts: 1,725
  • Member since Jul '12
  • Seattle, WA
    • View Profile
    • My build thread
Yesterday I made some EGR block off plates. I had a big 1-1/2" thick chunk of aluminum so I cut a block out of it then cut a 3/4" thick slice and a 3/8" slice from that block then cut them to shape and sanded them to dimension on the belt sander. Lastly, I have a ceramic tile with a sheet of 220 grit glued to it that I use for surfacing. That got it pretty flat so that they would seal. I also bolted the intake and air conditioning pump on. starting to look pretty complete. I was thinking that I might fire it off today but I can't find my water pump pulley :smack: I ordered one on Ebay. So when it gets here in November I should be good to go.
-1987 SR5 4runner, 1KZ-t turbo diesel with mech. pump
 & custom 3" S.S. dump pipe, R-151f transmission, marlin dual ultimate transfer cases w/ triple shifter, SAS, 35's https://board.marlincrawler.com/index.php?topic=98969.0
-1984 SR5 Tercel 4wd wagon bone stock - given to my nephew https://board.marlincrawler.com/index.php?topic=100547.0
-1:10 scale RC 4wd crawler w/yota axles, R2 2 speed enclosed dig tranny and 1st gen 4Runner body by BigBird
-My front axle service write-up http://board.marlincrawler.com/i

helipilot77 [OP]

  • Offline The 1.5K Club
  • **
  • Turtle Points: 1018
  • Male Posts: 1,725
  • Member since Jul '12
  • Seattle, WA
    • View Profile
    • My build thread
Parts are in! Thanks to Dave Stedman at Japan4x4.com

« Last Edit: Sep 04, 2018, 12:38:05 PM by helipilot77 »
-1987 SR5 4runner, 1KZ-t turbo diesel with mech. pump
 & custom 3" S.S. dump pipe, R-151f transmission, marlin dual ultimate transfer cases w/ triple shifter, SAS, 35's https://board.marlincrawler.com/index.php?topic=98969.0
-1984 SR5 Tercel 4wd wagon bone stock - given to my nephew https://board.marlincrawler.com/index.php?topic=100547.0
-1:10 scale RC 4wd crawler w/yota axles, R2 2 speed enclosed dig tranny and 1st gen 4Runner body by BigBird
-My front axle service write-up http://board.marlincrawler.com/i

helipilot77 [OP]

  • Offline The 1.5K Club
  • **
  • Turtle Points: 1018
  • Male Posts: 1,725
  • Member since Jul '12
  • Seattle, WA
    • View Profile
    • My build thread
Got some more work done yesterday. Nothing worth photographing. Plugged in electrical connections, installed pulley and belts. Installed hoses, power steering lines and fluid reservoir.
« Last Edit: Sep 09, 2018, 09:52:40 PM by helipilot77 »
-1987 SR5 4runner, 1KZ-t turbo diesel with mech. pump
 & custom 3" S.S. dump pipe, R-151f transmission, marlin dual ultimate transfer cases w/ triple shifter, SAS, 35's https://board.marlincrawler.com/index.php?topic=98969.0
-1984 SR5 Tercel 4wd wagon bone stock - given to my nephew https://board.marlincrawler.com/index.php?topic=100547.0
-1:10 scale RC 4wd crawler w/yota axles, R2 2 speed enclosed dig tranny and 1st gen 4Runner body by BigBird
-My front axle service write-up http://board.marlincrawler.com/i

Rockcrawlintoy

  • 4 doors for more whores
  • Offline The 2K Group
  • ***
  • Turtle Points: 2120
  • Male Posts: 2,336
  • Member since Dec '03
  • RIP Kyle
    • View Profile
    • Buy me a soda
So how long til startup
Resident Jeep Guy
2007 JKU All Stock
ECV 7-11

helipilot77 [OP]

  • Offline The 1.5K Club
  • **
  • Turtle Points: 1018
  • Male Posts: 1,725
  • Member since Jul '12
  • Seattle, WA
    • View Profile
    • My build thread
I’m really hoping to fire it up next weekend. Want to come help or laugh when it blows up? I’m so nervous.
-1987 SR5 4runner, 1KZ-t turbo diesel with mech. pump
 & custom 3" S.S. dump pipe, R-151f transmission, marlin dual ultimate transfer cases w/ triple shifter, SAS, 35's https://board.marlincrawler.com/index.php?topic=98969.0
-1984 SR5 Tercel 4wd wagon bone stock - given to my nephew https://board.marlincrawler.com/index.php?topic=100547.0
-1:10 scale RC 4wd crawler w/yota axles, R2 2 speed enclosed dig tranny and 1st gen 4Runner body by BigBird
-My front axle service write-up http://board.marlincrawler.com/i

Rockcrawlintoy

  • 4 doors for more whores
  • Offline The 2K Group
  • ***
  • Turtle Points: 2120
  • Male Posts: 2,336
  • Member since Dec '03
  • RIP Kyle
    • View Profile
    • Buy me a soda
I’ll talk to the wife see what’s goin on next weekend
Resident Jeep Guy
2007 JKU All Stock
ECV 7-11

helipilot77 [OP]

  • Offline The 1.5K Club
  • **
  • Turtle Points: 1018
  • Male Posts: 1,725
  • Member since Jul '12
  • Seattle, WA
    • View Profile
    • My build thread
-1987 SR5 4runner, 1KZ-t turbo diesel with mech. pump
 & custom 3" S.S. dump pipe, R-151f transmission, marlin dual ultimate transfer cases w/ triple shifter, SAS, 35's https://board.marlincrawler.com/index.php?topic=98969.0
-1984 SR5 Tercel 4wd wagon bone stock - given to my nephew https://board.marlincrawler.com/index.php?topic=100547.0
-1:10 scale RC 4wd crawler w/yota axles, R2 2 speed enclosed dig tranny and 1st gen 4Runner body by BigBird
-My front axle service write-up http://board.marlincrawler.com/i

THK Matt

  • 96ZJ v8
  • Offline Gold Turtle Award
  • *
  • Turtle Points: -415
  • Male Posts: 4,823
  • Member since Jun '07
    • View Profile
    • Buy me a drink
:willynilly: runnn!! its gonna blow!!!


she lives!
2007 GMC Yukon SLT Daily
5.3L V8, 3.5in Lift, 33X10.5R18 Toyo MTs, Vision Rocker 18x9s powdercoated Mountain Blue Transparent over Speedboat Aluminum

2010 Chevy Tahoe LT Wife's Daily
5.3L V8, 6in Lift, 35s, AMP power steps

2016 Ford F250 XLT CCLB Work/Business Truck
6.2L V8

2001 Ford F350 Lariat CCLB Work/Business Truck
7.3L Powerstroke w/ Banks Turbo

Instagram @ taytershubby13

emsvitil

  • Offline Silver Turtle Award
  • *
  • Turtle Points: 7571
  • Male Posts: 3,561
  • Member since May '07
    • View Profile
    • emsvitil's album
    • Buy me a soda

Sounds like your rods are knocking...……






 :smack:


 :yupyup:


 :cheese:
Ed
SoCal
86 SR5 XtraCab
22RE  W56B
31x10.50R15

OVRAROK

  • Offline Silver Turtle Award
  • *
  • Turtle Points: 26739
  • Male Posts: 3,500
  • Member since Dec '10
    • View Profile
Is there oil in it....
Even the most primitive society, has an intimate respect for the insane.

helipilot77 [OP]

  • Offline The 1.5K Club
  • **
  • Turtle Points: 1018
  • Male Posts: 1,725
  • Member since Jul '12
  • Seattle, WA
    • View Profile
    • My build thread
That’s called diesel knock. It means my timing needs to be adjusted. My dad’s Yanmar tractor always sounds like that. My oil pressure gauge wasn’t giving me a reading so to make sure I had oil pressure zippo and I ran to O’reilly’s to get a mechanical oil pressure gauge. It was putting out between 40 and 50 psi. I’m hoping that when I hook up the intake constrictor control the ECU will sense it and adjust the timing.
« Last Edit: Sep 17, 2018, 03:08:29 PM by helipilot77 »
-1987 SR5 4runner, 1KZ-t turbo diesel with mech. pump
 & custom 3" S.S. dump pipe, R-151f transmission, marlin dual ultimate transfer cases w/ triple shifter, SAS, 35's https://board.marlincrawler.com/index.php?topic=98969.0
-1984 SR5 Tercel 4wd wagon bone stock - given to my nephew https://board.marlincrawler.com/index.php?topic=100547.0
-1:10 scale RC 4wd crawler w/yota axles, R2 2 speed enclosed dig tranny and 1st gen 4Runner body by BigBird
-My front axle service write-up http://board.marlincrawler.com/i

helipilot77 [OP]

  • Offline The 1.5K Club
  • **
  • Turtle Points: 1018
  • Male Posts: 1,725
  • Member since Jul '12
  • Seattle, WA
    • View Profile
    • My build thread
Well, yesterday I hooked up the intake constrictor control. It made no noticeable improvement on the timing. So next step is to take the front cover off and see if I somehow installed one of the timing gears a tooth off.  :smack:
-1987 SR5 4runner, 1KZ-t turbo diesel with mech. pump
 & custom 3" S.S. dump pipe, R-151f transmission, marlin dual ultimate transfer cases w/ triple shifter, SAS, 35's https://board.marlincrawler.com/index.php?topic=98969.0
-1984 SR5 Tercel 4wd wagon bone stock - given to my nephew https://board.marlincrawler.com/index.php?topic=100547.0
-1:10 scale RC 4wd crawler w/yota axles, R2 2 speed enclosed dig tranny and 1st gen 4Runner body by BigBird
-My front axle service write-up http://board.marlincrawler.com/i

helipilot77 [OP]

  • Offline The 1.5K Club
  • **
  • Turtle Points: 1018
  • Male Posts: 1,725
  • Member since Jul '12
  • Seattle, WA
    • View Profile
    • My build thread
The replacement turbo union I ordered arrived from Japan while I was at H8PVMNT's goofing off.

-1987 SR5 4runner, 1KZ-t turbo diesel with mech. pump
 & custom 3" S.S. dump pipe, R-151f transmission, marlin dual ultimate transfer cases w/ triple shifter, SAS, 35's https://board.marlincrawler.com/index.php?topic=98969.0
-1984 SR5 Tercel 4wd wagon bone stock - given to my nephew https://board.marlincrawler.com/index.php?topic=100547.0
-1:10 scale RC 4wd crawler w/yota axles, R2 2 speed enclosed dig tranny and 1st gen 4Runner body by BigBird
-My front axle service write-up http://board.marlincrawler.com/i

:)bestgen4runner

  • Offline The 1.5K Club
  • **
  • Turtle Points: 2120
  • Male Posts: 1,794
  • Member since Mar '16
  • Crawling with Marlin
    • View Profile
Any answer to the poor running and sounding concern?  :therethere:
Or did I miss it in the shout box at some point?
I am 1/5th of Perfect Fit
SqWADoosh [04:19 PM]: *sigh* I guess Chris is right and I just need to wait until I'm in a place where I have a tow rig and trailer before I get this caliber of truck
Mudder [08:28 PM]:   not try to be a jerk, but are you serious bestgen?
Prismo [06:11 PM]:   Done, time to relax or as Bestgen says....FREEDOM!
HogCanyonHopper [06:54 PM]:   I like my little rod. it gets the job done
H8PVMNT [03:30 PM]: I can go both ways.

helipilot77 [OP]

  • Offline The 1.5K Club
  • **
  • Turtle Points: 1018
  • Male Posts: 1,725
  • Member since Jul '12
  • Seattle, WA
    • View Profile
    • My build thread
I’m not much of a shouter. I have been out of town for the last two weeks. You missed nothing.
-1987 SR5 4runner, 1KZ-t turbo diesel with mech. pump
 & custom 3" S.S. dump pipe, R-151f transmission, marlin dual ultimate transfer cases w/ triple shifter, SAS, 35's https://board.marlincrawler.com/index.php?topic=98969.0
-1984 SR5 Tercel 4wd wagon bone stock - given to my nephew https://board.marlincrawler.com/index.php?topic=100547.0
-1:10 scale RC 4wd crawler w/yota axles, R2 2 speed enclosed dig tranny and 1st gen 4Runner body by BigBird
-My front axle service write-up http://board.marlincrawler.com/i

helipilot77 [OP]

  • Offline The 1.5K Club
  • **
  • Turtle Points: 1018
  • Male Posts: 1,725
  • Member since Jul '12
  • Seattle, WA
    • View Profile
    • My build thread
Yesterday I spent some time diagnosing the poor running problem. I made sure that the vacuum pump was building good vacuum so it could properly operate the VSV's, which it was so I then checked if the turbo was building boost, it also was working properly. I decided that just to be sure that there weren't any codes stored in the ECU I should put it in Diagnostic mode and check the memory. This is where things get strange. When the key is first turned to the on position the Check Engine Light should be illuminated and should typically stay illuminated until the engine is started. When the ECU is in diagnostic mode it should do the same for a few seconds and then proceed to flash any codes that are stored in memory. My Check Engine Light never came on in either normal or diagnostic mode. I put an LED bulb in place of the incandescent bulb years ago, so I know it isn't burned out. first thing I checked were that the engine and subsequently the sensors all had a good ground. Yes. then I checked that the ECU grounds were all in good working order, which I was unable to complete because I had to leave. So that's where I'm at. Hopefully it's nothing major. This is why a mechanical pump would be so nice. No electronics to troubleshoot. I had to leave town yet again so it'll be another week till I can finish troubleshooting the ECU grounds.
-1987 SR5 4runner, 1KZ-t turbo diesel with mech. pump
 & custom 3" S.S. dump pipe, R-151f transmission, marlin dual ultimate transfer cases w/ triple shifter, SAS, 35's https://board.marlincrawler.com/index.php?topic=98969.0
-1984 SR5 Tercel 4wd wagon bone stock - given to my nephew https://board.marlincrawler.com/index.php?topic=100547.0
-1:10 scale RC 4wd crawler w/yota axles, R2 2 speed enclosed dig tranny and 1st gen 4Runner body by BigBird
-My front axle service write-up http://board.marlincrawler.com/i

redneckcustoms13

  • Offline The 2.5K Group
  • ****
  • Turtle Points: 7674
  • Male Posts: 2,513
  • Member since May '15
    • View Profile
    • Buy me a beer
I know it sounds silly, but what about removing that bulb and testing it or replace it with an incandescent just to see if the circuit works?
83 long bed 2wd sas, 3rz, w56, duals with 4.7 rear, 4.88 elock front, spartan rear, 39.5 iroks
01 double cab hunting truck
06 tacoma street truck

Gnarly4X

  • Offline Gold Turtle Award
  • *
  • Turtle Points: 5143
  • Male Posts: 4,210
  • Member since Jun '16
  • 4-wheeling vicariously.
    • View Profile
    • Buy me some coffee
Just a couple thoughts…

Have you cleaned your battery terminals and clamps? Have you checked the voltage the alternator is putting out?

I would disconnect the battery for an hour and let the ECU reset.

Also, I believe the CEL can come on and go off if it does not detect a major voltage change from the sensors. If there is a detectable drop in voltage, then you can check for codes and go from there.

Gnarls. :blah:
1986 XtraCab SR5 22RE 5speed W56B, ~16,000 MI after break-in, DIM (Did It Myself) rebuilt engine - .020" over, engnbldr RV head, OS valves, 261C cam, DT Header. https://imgur.com/oACTHTR

God Bless Our Troops... Especially Our Snipers. The 2nd defends the 1st
MEMBER: WWP, T2T, VFW, NRA, GOA, SAF, Mammoth Nation, C2 Tactical, Hillsdale College, Humane Society of the U.S. - "We cannot solve our problems with the same thinking we used to create them." ~ Albert Einstein

zippo

  • Offline The 1.5K Club
  • **
  • Turtle Points: 569
  • Male Posts: 1,554
  • Member since Nov '08
    • View Profile
    • oppiz.net
If you see it, its for sale.

helipilot77 [OP]

  • Offline The 1.5K Club
  • **
  • Turtle Points: 1018
  • Male Posts: 1,725
  • Member since Jul '12
  • Seattle, WA
    • View Profile
    • My build thread
I know a guy in Portland who just finished a swap into a second gen 4runner. He used one of their mechanical pumps. He really likes it. Steve has a 3L mechanical pump. I think it might be the same pump body as the one used on the 1KZ-t that came from the factory with a mechanical pump. I would just need to have ot tuned for the 1KZ. Trying to find a cheaper way to get a mech pump on this thing.
-1987 SR5 4runner, 1KZ-t turbo diesel with mech. pump
 & custom 3" S.S. dump pipe, R-151f transmission, marlin dual ultimate transfer cases w/ triple shifter, SAS, 35's https://board.marlincrawler.com/index.php?topic=98969.0
-1984 SR5 Tercel 4wd wagon bone stock - given to my nephew https://board.marlincrawler.com/index.php?topic=100547.0
-1:10 scale RC 4wd crawler w/yota axles, R2 2 speed enclosed dig tranny and 1st gen 4Runner body by BigBird
-My front axle service write-up http://board.marlincrawler.com/i

:)bestgen4runner

  • Offline The 1.5K Club
  • **
  • Turtle Points: 2120
  • Male Posts: 1,794
  • Member since Mar '16
  • Crawling with Marlin
    • View Profile
Nate, when You say that You checked the power and grounds? voltage drop or just test light?
I am 1/5th of Perfect Fit
SqWADoosh [04:19 PM]: *sigh* I guess Chris is right and I just need to wait until I'm in a place where I have a tow rig and trailer before I get this caliber of truck
Mudder [08:28 PM]:   not try to be a jerk, but are you serious bestgen?
Prismo [06:11 PM]:   Done, time to relax or as Bestgen says....FREEDOM!
HogCanyonHopper [06:54 PM]:   I like my little rod. it gets the job done
H8PVMNT [03:30 PM]: I can go both ways.

helipilot77 [OP]

  • Offline The 1.5K Club
  • **
  • Turtle Points: 1018
  • Male Posts: 1,725
  • Member since Jul '12
  • Seattle, WA
    • View Profile
    • My build thread
Nate, when You say that You checked the power and grounds? voltage drop or just test light?
I haven’t checked the power yet but when i was checking the grounds i was using an ohmeter checking for continuity.
-1987 SR5 4runner, 1KZ-t turbo diesel with mech. pump
 & custom 3" S.S. dump pipe, R-151f transmission, marlin dual ultimate transfer cases w/ triple shifter, SAS, 35's https://board.marlincrawler.com/index.php?topic=98969.0
-1984 SR5 Tercel 4wd wagon bone stock - given to my nephew https://board.marlincrawler.com/index.php?topic=100547.0
-1:10 scale RC 4wd crawler w/yota axles, R2 2 speed enclosed dig tranny and 1st gen 4Runner body by BigBird
-My front axle service write-up http://board.marlincrawler.com/i

:)bestgen4runner

  • Offline The 1.5K Club
  • **
  • Turtle Points: 2120
  • Male Posts: 1,794
  • Member since Mar '16
  • Crawling with Marlin
    • View Profile
I haven’t checked the power yet but when i was checking the grounds i was using an ohmeter checking for continuity.
I highly recommend testing using a voltage drop. A continuity tests will pass when a voltage drop will fail and show You the problem. 
Seen it many times.  :twocents:
I am 1/5th of Perfect Fit
SqWADoosh [04:19 PM]: *sigh* I guess Chris is right and I just need to wait until I'm in a place where I have a tow rig and trailer before I get this caliber of truck
Mudder [08:28 PM]:   not try to be a jerk, but are you serious bestgen?
Prismo [06:11 PM]:   Done, time to relax or as Bestgen says....FREEDOM!
HogCanyonHopper [06:54 PM]:   I like my little rod. it gets the job done
H8PVMNT [03:30 PM]: I can go both ways.

 
 
 
 
 

Related Topics

35 Replies
11989 Views
Last post Feb 06, 2009, 09:36:31 PM
by twistedtoy92
79 Replies
30638 Views
Last post Oct 14, 2010, 09:39:10 AM
by Fleetwood
2 Replies
2148 Views
Last post Nov 26, 2008, 11:19:26 AM
by JohnHalladay
1 Replies
1863 Views
Last post Jun 19, 2009, 10:25:10 AM
by Pat
5 Replies
2015 Views
Last post Jul 17, 2020, 10:49:44 AM
by FjordWarrden