Author Topic: L50 shifter stuck (Read 2054 times)

superyota · « **on:** Oct 25, 2010, 11:12:30 AM »

I pulled the cover with the shift forks off of my L50 to check the gears and syncros before i installed it. now, i put it back on, and as far as i can tell, everything is lined up, shift forks in place. but when its all back together, the shifter doesn't move. any ideas?

79coyotefrg · « **Reply #1 on:** Oct 27, 2010, 09:24:50 PM »

you have it in 2 gears remove the cover again and make sure everything is in neutral

superyota · « **Reply #2 on:** Oct 28, 2010, 10:20:02 AM »

sorry for the stupid question, but if i spin the input shaft, and i can hold the output to where its not spinning, thats neutral, right?

superyota · « **Reply #3 on:** Oct 28, 2010, 10:21:13 AM »

also, reverse gear was showing a little(minimal) wear on the edge. should i change out the gear, or leave it alone?

79coyotefrg · « **Reply #4 on:** Oct 28, 2010, 10:43:57 AM »

Quote from: superyota on Oct 28, 2010, 10:20:02 AM

sorry for the stupid question, but if i spin the input shaft, and i can hold the output to where its not spinning, thats neutral, right?

right

Quote from: superyota on Oct 28, 2010, 10:21:13 AM

also, reverse gear was showing a little(minimal) wear on the edge. should i change out the gear, or leave it alone?

leave it alone

superyota · « **Reply #5 on:** Oct 28, 2010, 10:53:00 AM »

thanks for the info. i'll give it a shot.

Author Topic: L50 shifter stuck (Read 2054 times)

superyota

L50 shifter stuck

79coyotefrg

Re: L50 shifter stuck

superyota [OP]

Re: L50 shifter stuck

superyota [OP]

Re: L50 shifter stuck

79coyotefrg

Re: L50 shifter stuck

superyota [OP]

Re: L50 shifter stuck

Related Topics


	Author Topic: L50 shifter stuck (Read 2054 times) 0 Members and 1 Guest are viewing this topic. superyota Prestige Worldwide Silver Turtle Award Turtle Points: 71 Posts: 3,362 Member since Oct '05 what happened? L50 shifter stuck « on: Oct 25, 2010, 11:12:30 AM » I pulled the cover with the shift forks off of my L50 to check the gears and syncros before i installed it. now, i put it back on, and as far as i can tell, everything is lined up, shift forks in place. but when its all back together, the shifter doesn't move. any ideas? Logged ABD Motorsports #4475 If you can't convince them, confuse them. Placer County Crawlers - President 2011-2016 www.placercountycrawlers.com Rubicon Trail Foundation - Property Committee member Friends of Fordyce - Board Member KK6QDW 79coyotefrg Rock Ninja Gold Turtle Award Turtle Points: 1452 Posts: 22,633 Member since May '02 Solid axle Toys Rule ! ! ! Re: L50 shifter stuck « Reply #1 on: Oct 27, 2010, 09:24:50 PM » you have it in 2 gears remove the cover again and make sure everything is in neutral Logged AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/ 32/36weber, Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears RIP Nitro 9-29-07 I sure miss him $I\'m Down$ MarlinCrawlerInc IS NOT affiliated with TrailGear in any way superyota [OP] Prestige Worldwide Silver Turtle Award Turtle Points: 71 Posts: 3,362 Member since Oct '05 what happened? Re: L50 shifter stuck « Reply #2 on: Oct 28, 2010, 10:20:02 AM » sorry for the stupid question, but if i spin the input shaft, and i can hold the output to where its not spinning, thats neutral, right? Logged ABD Motorsports #4475 If you can't convince them, confuse them. Placer County Crawlers - President 2011-2016 www.placercountycrawlers.com Rubicon Trail Foundation - Property Committee member Friends of Fordyce - Board Member KK6QDW superyota [OP] Prestige Worldwide Silver Turtle Award Turtle Points: 71 Posts: 3,362 Member since Oct '05 what happened? Re: L50 shifter stuck « Reply #3 on: Oct 28, 2010, 10:21:13 AM » also, reverse gear was showing a little(minimal) wear on the edge. should i change out the gear, or leave it alone? Logged ABD Motorsports #4475 If you can't convince them, confuse them. Placer County Crawlers - President 2011-2016 www.placercountycrawlers.com Rubicon Trail Foundation - Property Committee member Friends of Fordyce - Board Member KK6QDW 79coyotefrg Rock Ninja Gold Turtle Award Turtle Points: 1452 Posts: 22,633 Member since May '02 Solid axle Toys Rule ! ! ! Re: L50 shifter stuck « Reply #4 on: Oct 28, 2010, 10:43:57 AM » Quote from: superyota on Oct 28, 2010, 10:20:02 AM sorry for the stupid question, but if i spin the input shaft, and i can hold the output to where its not spinning, thats neutral, right? right Quote from: superyota on Oct 28, 2010, 10:21:13 AM also, reverse gear was showing a little(minimal) wear on the edge. should i change out the gear, or leave it alone? leave it alone Logged AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/ 32/36weber, Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears RIP Nitro 9-29-07 I sure miss him $I\'m Down$ MarlinCrawlerInc IS NOT affiliated with TrailGear in any way superyota [OP] Prestige Worldwide Silver Turtle Award Turtle Points: 71 Posts: 3,362 Member since Oct '05 what happened? Re: L50 shifter stuck « Reply #5 on: Oct 28, 2010, 10:53:00 AM » thanks for the info. i'll give it a shot. Logged ABD Motorsports #4475 If you can't convince them, confuse them. Placer County Crawlers - President 2011-2016 www.placercountycrawlers.com Rubicon Trail Foundation - Property Committee member Friends of Fordyce - Board Member KK6QDW