Glen's budget rebuild

Started by 79coyotefrg, September 26, 2004, 05:30:02 PM

0 Members and 38 Guests are viewing this topic.

DanS

Glen, as tough as you are there are limits the human body can take. For several years 'my' doctor and chiro-quack told me my back pains where my imagination only. After 4 hours under the knife I'm left with a permanent limp and re-occuring back problems. All of which that could have been avoided had I seen a 'real' Doctor immediately after my accident!!!!!!!!!!!!!   :hammer:
Take the time to see real Doctors and applicable specialists, there will be nothing worse than not being able to wrench, drive or enjoy life because of an accident that was not of your fault.
DanS
Wow, been looking at my 4Runner rust away too long, need some inspiration and here I will find it...!

85 Toyota 4Runner, solid axle, 22Re, original paint and graphics and not a straight panel to be found!

79coyotefrg

oh i totally agree,  and i am seeing a  REAL doctor tomorrow  if i can get past his receptionist  that demands  $43  up front,  but  i THINK  i have that covered,    just  dont know  if i'll have it in my hands  in time  if not  i'll just kick and scream  till they let me see him or i get throwed out  :disturbed:


my Dad  went for years with chest pain  because his regular doctor  said"well your old"  i took him to see the man  im seeing tomorrow  and  he said "you have a heart valve  problem"   2 weeks later  he had  seen a cardiologist, and was in surgery.


of course  little did we know  he would be allergic  to that drug  and  later die,  but that wasnt the doctors fault,  i truely believe  they did there best  and dont hold it against them,  in fact  i feel   some comfort  in seeing Dad's doctors  since they kinda know what to look for

the neck  is  ok,   nothing damaged besides soft tissue,  will get better with time  and therapy  but  will never be the same,
AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/    32/36weber, :driving: Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears    RIP Nitro 9-29-07 :(  I sure miss him :down: MarlinCrawlerInc IS NOT affiliated with TrailGear in any way

79coyotefrg

Infernal   you better get out here  in the spring
AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/    32/36weber, :driving: Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears    RIP Nitro 9-29-07 :(  I sure miss him :down: MarlinCrawlerInc IS NOT affiliated with TrailGear in any way

4inchToyotas

Quote from: unclejpl4x4 on October 08, 2007, 03:42:17 PM
is it done yet :dunno:

haha classic.

Looks like this thread needs to be retitled "Glen's no-so budget re-rebuild"
2006 Tundra DC 4x4 - DD/Tow (if I can ever find a place to store a trailer)
1983 Hilux - 20/22r Weber 32/36 carb, 4" ProComp suspension, 5.29's Lockrite Front, Spool rear, 34x10.50x15 LTBs

79coyotefrg

i was able to look over the donor truck  good today,  i think i'll need  to pull the wireing harness out  and use my harness

the previous  owner  of the donor  truck  had  spliced it to pieces  :shake:
AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/    32/36weber, :driving: Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears    RIP Nitro 9-29-07 :(  I sure miss him :down: MarlinCrawlerInc IS NOT affiliated with TrailGear in any way

79coyotefrg

and thats gonna be a  job  in itself :thud:
AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/    32/36weber, :driving: Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears    RIP Nitro 9-29-07 :(  I sure miss him :down: MarlinCrawlerInc IS NOT affiliated with TrailGear in any way

79coyotefrg

well you've heard all the BAD  news,  now  for some good stuff  :love:

why he didnt want me to say who it was openly i dont know  but  SOMEONE thats a very sweet  dude,   :smooch:   sent me  a complete  Allpro hysteer kit  and some  5 inch front springs,  the springs havent got here yet but im hoping i can pull a leaf out  to bring them down a tad,  not sure my short, fat, crippled :moon:  could get in the truck with 5 inch springs  :ack:  but  if  it looks like the  integrity of the springs will suffer if i remove a leaf  i'll  just leav the body lift off  and  figure out what radiator to use later


:psss:  i was running a v6 radiator  that required 2 inch body lift  :shhh:



AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/    32/36weber, :driving: Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears    RIP Nitro 9-29-07 :(  I sure miss him :down: MarlinCrawlerInc IS NOT affiliated with TrailGear in any way

MiniSimp

Keep it low, no body lift, get a different radiator. 5" will be huge! NICE SCORE!
Just mount the front the same way the MC FToy is done and you'll be fine.
And send that dude some beer! :beerchug:

oddball

Thats awsome, my hat goes off to the mystery parts donater, a true standup person :thumbs:
2008 Tacoma regular cab, 4.88s, ARBs, crawl box, manual shift FJ case

79coyotefrg

Quote from: MiniSimp on October 15, 2007, 09:30:25 AM
Keep it low, no body lift, get a different radiator. 5" will be huge! NICE SCORE!
Just mount the front the same way the MC FToy is done and you'll be fine.
And send that dude some beer! :beerchug:
:haha:  if  i could  i'd send him a  strip-o-gram  :boobs:
AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/    32/36weber, :driving: Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears    RIP Nitro 9-29-07 :(  I sure miss him :down: MarlinCrawlerInc IS NOT affiliated with TrailGear in any way

79coyotefrg

so what you think  the  turbo  radiator :dunno:  whats Marlin run  ??  seems like he has the early diesel radiator  :headscratch:
AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/    32/36weber, :driving: Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears    RIP Nitro 9-29-07 :(  I sure miss him :down: MarlinCrawlerInc IS NOT affiliated with TrailGear in any way

THK Matt

the turbo is a 3row
run that =P
2007 GMC Yukon SLT Daily
5.3L V8, 3.5in Lift, 33X10.5R18 Toyo MTs, Vision Rocker 18x9s powdercoated Mountain Blue Transparent over Speedboat Aluminum

2010 Chevy Tahoe LT Wife's Daily
5.3L V8, 6in Lift, 35s, AMP power steps

2016 Ford F250 XLT CCLB Work/Business Truck
6.2L V8

2001 Ford F350 Lariat CCLB Work/Business Truck
7.3L Powerstroke w/ Banks Turbo

Instagram @ taytershubby13

Cheesemaker

Run that turbo radiator!  If not, call Mark!!  :yesnod:

I tried to get a turbo rad for mine, but the company I got mine from sold me one that was too tall, and I didn't want to modify anything to make one fit!  So, I got the regular stock one for now, until I can find a turbo one! 
Miss ya Dean (4THEWKN) & Kyle (KYOTA)!!

4THEWKN~9/17/2006  If it wasn't for you, I'd be driving something other than a Toyota!

My build up ~ project Kilchis! http://board.marlincrawler.com/index.php?topic=32961.0
Zak's truck build ~ http://board.marlincrawler.com/index.php?topic=64319.0;topicseen

79coyotefrg

thanks Ryan,  i'll try the  turbo radiator,  i know the V6 radiator  HAS  to have the body lift to work  and  the springs arrived this afternoon,  :woohoo:

i looked them over  i think i can remove a leaf  and be okay

i know my radiator  looks  like , well  it aint gonna work :down:
AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/    32/36weber, :driving: Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears    RIP Nitro 9-29-07 :(  I sure miss him :down: MarlinCrawlerInc IS NOT affiliated with TrailGear in any way

topar

Sounds Like Peps hooked you up like he did me and my brother gotta like the guy  :biggthumpup:  If it was him  :dunno:

THK Matt

try that turbo rad and let me know how you like it.
2007 GMC Yukon SLT Daily
5.3L V8, 3.5in Lift, 33X10.5R18 Toyo MTs, Vision Rocker 18x9s powdercoated Mountain Blue Transparent over Speedboat Aluminum

2010 Chevy Tahoe LT Wife's Daily
5.3L V8, 6in Lift, 35s, AMP power steps

2016 Ford F250 XLT CCLB Work/Business Truck
6.2L V8

2001 Ford F350 Lariat CCLB Work/Business Truck
7.3L Powerstroke w/ Banks Turbo

Instagram @ taytershubby13

79coyotefrg

Quote from: topar on October 15, 2007, 08:16:23 PM
Sounds Like Peps hooked you up like he did me and my brother gotta like the guy  :biggthumpup:  If it was him  :dunno:
:lipsrsealed:



:angel:
AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/    32/36weber, :driving: Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears    RIP Nitro 9-29-07 :(  I sure miss him :down: MarlinCrawlerInc IS NOT affiliated with TrailGear in any way

tom w.

So when do we get to see the new truck?

79coyotefrg

Quote from: tom w. on October 16, 2007, 09:02:20 AM
So when do we get to see the new truck?
as soon as i can afford  to get the pics from the camera on a cd  cause  it  is mad at my puter  :dunno:   they aint talking right now  :screwy:
AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/    32/36weber, :driving: Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears    RIP Nitro 9-29-07 :(  I sure miss him :down: MarlinCrawlerInc IS NOT affiliated with TrailGear in any way

sinbob

hey Glen tks for ur input today......and I don't know if this helps but I was lookin at my wifey's 97 camrey and she has a sweet radiator set up in it long, not to high with a dual fan setup.  anyway I almost didn't get out of there with my life when she found me measuring it to see if it would fit in my toy.  I will check it out and let u know when I can get her calmed down enough to let me back under her hood...car that is...lolol
take care.
85 flatbed, 22RE,Downey air, redtop, dual 2.28 crawler, high steer, Marlin clutch, 5.29's, ARB rear, lockright front, Warn hubs, wrangler 4" front-skyjacker 4" r-springs w/6" shackels, flip kit, 35x12.5x15 MTR's, sliders, belly, exocage.
:support our troops :usa:
They told me I had to grow old, but they never told me I had to grow up. :cheer:
"life is not measured by the number of breaths we take, but by the moments that take our breath away" :bananasplit:
Life is not about waiting for the storm to pass, but learning to dance in the rain :dancing:

4inchToyotas

So the engine faired well enough?
2006 Tundra DC 4x4 - DD/Tow (if I can ever find a place to store a trailer)
1983 Hilux - 20/22r Weber 32/36 carb, 4" ProComp suspension, 5.29's Lockrite Front, Spool rear, 34x10.50x15 LTBs

79coyotefrg

Quote from: sinbob on October 16, 2007, 11:24:53 AM
hey Glen tks for ur input today......and I don't know if this helps but I was lookin at my wifey's 97 camrey and she has a sweet radiator set up in it long, not to high with a dual fan setup.  anyway I almost didn't get out of there with my life when she found me measuring it to see if it would fit in my toy.  I will check it out and let u know when I can get her calmed down enough to let me back under her hood...car that is...lolol
take care.
:rofl:   dont get dead  :rofl:
AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/    32/36weber, :driving: Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears    RIP Nitro 9-29-07 :(  I sure miss him :down: MarlinCrawlerInc IS NOT affiliated with TrailGear in any way

79coyotefrg

Quote from: 4inchToyotas on October 17, 2007, 07:21:43 AM
So the engine faired well enough?
as best i can tell it came out ok,  waiting for the all clear from the insurance company  before i start whackin at it
AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/    32/36weber, :driving: Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears    RIP Nitro 9-29-07 :(  I sure miss him :down: MarlinCrawlerInc IS NOT affiliated with TrailGear in any way

Cheesemaker

Make sure your OK before you go wrenching!  I wish I lived closer, I'd love to help out!
Miss ya Dean (4THEWKN) & Kyle (KYOTA)!!

4THEWKN~9/17/2006  If it wasn't for you, I'd be driving something other than a Toyota!

My build up ~ project Kilchis! http://board.marlincrawler.com/index.php?topic=32961.0
Zak's truck build ~ http://board.marlincrawler.com/index.php?topic=64319.0;topicseen

79coyotefrg

Quote from: cheesemaker on October 18, 2007, 01:54:29 AM
Make sure your OK before you go wrenching!  I wish I lived closer, I'd love to help out!
i wish you lived closer too,  im out of cheese  :cheese:

but seriously,  yea  im not physically  "ready"  yet  but  im gonna have help this weekend to get the donor truck off the trailer  and get some roller  tires  under it
AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/    32/36weber, :driving: Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears    RIP Nitro 9-29-07 :(  I sure miss him :down: MarlinCrawlerInc IS NOT affiliated with TrailGear in any way

79coyotefrg

 :outtahere:
AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/    32/36weber, :driving: Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears    RIP Nitro 9-29-07 :(  I sure miss him :down: MarlinCrawlerInc IS NOT affiliated with TrailGear in any way

79coyotefrg

 :snare:
AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/    32/36weber, :driving: Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears    RIP Nitro 9-29-07 :(  I sure miss him :down: MarlinCrawlerInc IS NOT affiliated with TrailGear in any way

Wermz84

I like to Drive!

79coyotefrg

 :sick:
AR-TTORA founder 22R bored.060,LCE stage II race cam http://pure-gas.org/    32/36weber, :driving: Marlin 1200 NON ceramic clutch, L52SHD+dualcase #2919, cable-locker, Yukon 5.29 gears, 35's, Allpro ebrake, front springs, and high steer, F150rears    RIP Nitro 9-29-07 :(  I sure miss him :down: MarlinCrawlerInc IS NOT affiliated with TrailGear in any way

Willy Mammoth



Cool   :eyebrow:

Nice paint job on the other one, have we seen that one before?

BTW, did you get any stickers with the high steer? I guess it is only fair to sport them huh.
:usa: American by birth, redneck by choice. 

Making Of http://board.marlincrawler.com/index.php?topic=6472.0  

Sightings Of  http://board.marlincrawler.com/index.php?topic=10805.0