Topic: MCR check list!! The clock it ticking

[Blingn]

Loaded all my gear today, wed night ill load up on the trailer and head out thursday morning.

cant wait to see the jeep in action and have some 's with ya  man. 

[Ruggedjeep]

Looking forward to it. I dont know who ill be wheeling with. If i get there early thursday ill be starting then, if not then fri morning it is.

[Wermz84]

Double check all fluids,

buy groceries,

pack.

[*FFC*]

>New rear driveshaft
>Flip rear leafs
>Install Tcase
>Install new brakes (rear)
>New starter (Or figure out why it won't start on its own)
>Install Front Shocks
>Install Rear Shocks
>Mount/remount rock lights
>Smog
>Register
>Insure 
>Inspect/replace pass wheel bearing  
>grocery shopping
>buy mom an air mattress




>Install new thirds

[L.D.]

well, done with most of the prep/repairs. all I've got left is to change the seats, and have the tire shop clean all the souvenirs from the ducy out of the tires. pack the ice chest an some clean clothes an we're good to go.

[Hyena]

some how the list grew again.

find out why it won't start. 
finish bleeding power steering.
fix alternator fuse. (broke into a million pieces and won't come out)
find hole in tire and plug it.

[Blingn [OP]]

OK the f250 tow rigs brakes are done the fluids on that are checked.  The jeep needs fluids checked and bolts tightened.  The trailer needs new wood and the it is wired except for one of the running lights.  Got to pack up the spares and the tools and pack clothes.  Im very close

[*FFC*]

>New rear driveshaft
>Flip rear leafs
>Install Tcase
>Install new brakes (rear)
>New starter (Or figure out why it won't start on its own)
>Install Front Shocks
>Install Rear Shocks EFF IT!!! I spent 3 hours yesterday prepping the mounts, cleaning the axle and the crossmember under the cab.  I went to weld up the tabs and the weld just bounces off the crossmember! So EFF EM!!! I got front shocks that's what matters


Carrying on...
>Mount/remount rock lights
>Smog
>Register
>Insure 
>Inspect/replace pass wheel bearing  
>grocery shopping
>buy mom an air mattress




>Install new thirds

[Rockcrawlintoy]

] EFF IT!!! I spent 3 hours yesterday prepping the mounts, cleaning the axle and the crossmember under the cab.  I went to weld up the tabs and the weld just bounces off the crossmember! So EFF EM!!! I got front shocks that's what matters
:

make sure u have a good ground and then try it again

Drew

[*FFC*]

make sure u have a good ground and then try it again

Drew

I did, I had the ground all over the place trying different grounding points. 

[Duffil]

are you ARCing or MIGing? Well, technically FCAWing, but anyway which are you using?

[*FFC*]

are you ARCing or MIGing? Well, technically FCAWing, but anyway which are you using?

I was using the MIG.  I was too close to fuel lines for using the ARC.

[*FFC*]

>New rear driveshaft
>Flip rear leafs
>Install Tcase
>Install new brakes (rear)
>New starter (Or figure out why it won't start on its own)
>Install Front Shocks
>Install Rear Shocks EFF IT!!! I spent 3 hours yesterday prepping the mounts, cleaning the axle and the crossmember under the cab.  I went to weld up the tabs and the weld just bounces off the crossmember! So EFF EM!!! I got front shocks that's what matters


Carrying on...
>Mount/remount rock lights
>Smog
>Register
>Insure 
>Inspect/replace pass wheel bearing  
>grocery shopping
>buy mom an air mattress




>Install new thirds

[93tonkatoy]

Looks like somebody needs to try out the new "grocery-getter"



and don't let no soccer mom in their wanna-be pavement pounding "sport-utility" POS take your parking spot!!!!