Topic: MEMBER MOD LIST

[V-Man]

Heres my pried and joy:


Let me know what you think, I love this truck and it'll out wheel anything you got

 I think you would need to buy  helmet, and some chainsaws to mount out front( if you don't think you need to back up) . Were I wheel the lower branches of the tree are only nine feet off the ground at best.  If the top of the snorkle is 15' off the ground that would put most of your truck ABOVE the branches.. I these are not little willow branches..    Your welcome to join me any time you like just duck..

[crawlerdan [OP]]

Heres my pried and joy:

1983 Shortbed
costum 15" drop hangars all arounds
custom invisble driveshafts so I dont hit dem rocks
savage roll bar
jeep yj axles cuz dem toyoda ones are crap
33" super gumbo jumbo mud dogs that tear it up
18 procomp shocks(these things rock) with custom flat black and chrome paint
single transfer case cause those duals were just too slow and I got confused with all dose shifers
24 8" hella lights with smiley face covers
pvc snorkl for that goes to 15' off ground
swaped in 3.0 liter
super beefy smitty built bumpers
ramped out 8.5" then rolled

Let me know what you think, I love this truck and it'll out wheel anything you got

girl thingy, that is all

[DTB]

girl thingy, that is all

No, the title of his own picture says it all.  Besides mine can outwheel his anyday. 

[V-Man]

No, the title of his own picture says it all.  Besides mine can outwheel his anyday. 

  Hey, now lets not be too hard on the BOY, he is at least honest about it..

 I never noticed the Image title the first time I read it..

  Also he can't drive down a lot of streets as the clearance for some overpasses, and ALL telephone and electrical wires in a residential area are 13'6"  MIN...  When he come to a over pass he had better know the clearance or his head going to    and whats left of him will be    on the pavement..

[wa4x4]

Dude is that a front bumper on the back???

My truck:
Invisible paint, 0psi in invisable tires, oh and a 3.0

[CrazyYota]

NICE hangars

[crawlerdan [OP]]

NICE hangars

   

[toybuilt]

toybuilt...............Aaron

I own a 1983 Toyota truck longbed. I'm in the middle of rebuilding it again though.

Engine.............soon to be rebuilt 4.3 Chevy V6
Transmission.....soon to be grany 4 speed
Transfer cases...soon to be klune V and 205 with FWD
Front Axle.........Dana 60, 4.56 gears, 35 spline inner and outer shafts, spicier u joints, ARB air locker, high steer with tie rod in back
Rear Axle..........14 bolt, 4.56 gears, Detroit locker, shaved, disk brake conversion
Suspension........Rancho 44044's in front, 63" Chevy spring with 2.5" blocks and drop down swivel shackels in rear
Tires................soon to be 39.5x15x17 TSL's with soft 8 17x10 rims

Bed is bobbed 18 inches with home built 2x4x.250 rap around rear bumper, sch. 80 rock sliders, drop box, inside cage, 3x2 rollbar

[crawlerdan [OP]]

toybuilt...............Aaron

I own a 1983 Toyota truck longbed. I'm in the middle of rebuilding it again though.

Engine.............soon to be rebuilt 4.3 Chevy V6
Transmission.....soon to be grany 4 speed
Transfer cases...soon to be klune V and 205 with FWD
Front Axle.........Dana 60, 4.56 gears, 35 spline inner and outer shafts, spicier u joints, ARB air locker, high steer with tie rod in back
Rear Axle..........14 bolt, 4.56 gears, Detroit locker, shaved, disk brake conversion
Suspension........Rancho 44044's in front, 63" Chevy spring with 2.5" blocks and drop down swivel shackels in rear
Tires................soon to be 39.5x15x17 TSL's with soft 8 17x10 rims

Bed is bobbed 18 inches with home built 2x4x.250 rap around rear bumper, sch. 80 rock sliders, drop box, inside cage, 3x2 rollbar

  get er done spanky, we all wanna see 40s, smokin in your driveway!!!!

[BLACKDOG]

BLACKDOG

1991 Xcab pickup

Went through 3 3.0s in 2005
4" suspension
3" body
63" chevies in the rear, pro comp stage II IFS lift
detroit rear, lockrite front
homebrew sliders (first welding experience ugly but they work)
1/4" angle iron rear braces (bumer was supposed to go on them, but didn't line up
stock t-case
warn hubs
net doors

[mudguts]

WOW, this thread went to . 

[shad]

Oh boy.....

1982 SR5 4x4 Pickup SWB

70k ish 22r top end redone 4/05
5" skyjacker soft ride front springs (www.jackit.com)
63" chevy silverado leaf springs
BudBuilt chevy spring hangers with skids (budbuilt)
BudBuilt 8" long 3/8" flatbar adjustable shackles (budbuilt)
with chevy shackle on top as a double shackle
Sky u-bolt filp front and rear www.sky-manufacturing.com
Ford F250 shock mounts Rancho 5000 RS5012 shocks on front
Rancho 5000 RS5012 shocks on rear
BudBuilt Low profile crossmember (www.budbuilt.com)
G54 transmission swap
new clutch
shortened rear driveshaft retubed with thicker od tubing
modifyed IFS front driveshaft
Triple drilled flanges on t-case and rear 3rd (www.Trail-gear.com)
1" Roger Brown Body lift
Sky Manufacturing Hysteer(www.roadlessgear.com)
FJ40 vented rotors drilled to IFS bolt on pattern (www.marlincrawler.com)
IFS front calipers
IFS hubs to widen front axle to 58"
FJ80 Master cylinder (www.marlincrawler.com)
Extended stainless flex brakelines (marlincrawler)
5.29 Yukon brand Motive gears (www.randysringandpinion.com)
Lockright locker rear (randys)
Aussie locker in front (www.aussielocker.com)
Longfeild cryo treated birfeilds (www.longfieldsuperaxles.com)
Stock inner axles that have been martac'ed
1.25" wheel spacers(www.marlincrawler.com) on back for now until I install the wider 87 toy truck axle
35x12.50 BFG MT's www.tirekingdom.com
15x8 3.5" BS series 51 procomp rock crawler rims www.4wheelparts.com
Custom DOM front bumper w/ 1/4" winch plate
Hella 500's mounted on it.
2 custom windsheild pillar light mounts with Hella 500's mounted to them.
62" long flatbed w/smittybuilt rollbar welded to it hella 550's mounted on it.
Custom mounts welded on for my 48" JackAll (same as a high-lift)
custom rear bumper w/ class III receiver.
87 Toyota MR2 adjustable seats
stock center console
Eclipse CD player 2 sets of speakers in doors 2ea 6 1/2's and 2ea 4 1/2's



MR2 seats those things are really nice...


At least I can clearly see my truck from my porch and can reach out and touch theives with my 12 gauge mossberg 500.

[BLACKDOG]

WOW, this thread went to . 

don't be  makin fun of my truck, just cause it don't run

[toybuilt]

 

[blackdiamond]

Aussie locker in front (www.aussielocker.com)
Longfeild cryo treated birfeilds (www.longfieldsuperaxles.com)
Stock inner axles that have been martac'ed

What do you think about your Aussie Locker?  How have the birfs/inner axles held up?

[shad]

T

What do you think about your Aussie Locker? How have the birfs/inner axles held up?

Aussie locker is great. I wish I had one in the back too. The lockright is way nosier and jerks a hell of alot more than the aussie does.
The Long treated Birf's have held up fine. As you you treat them nice they will last. My opinion 35's are fine to run with them.
However if you hammer on them and don't let off the gas they will eventually break.
I haven't broken one yet.


 

[BONER]

mine: complete marlin sas setup in front
         85 front axle with welded 93 v6 third member
         4 link rear with rubicon express zj 3.5 coils
         fuel cell,89 f250 fuel pump
         bilstein 5150's all around
         prelude buckets
         custom basher bumpers
         16.5 inch bed bob
         custom roof, and bed racks with bottle opener
         33 inch firestone destination m/t on black steelies
         frenched liscence plate light
         driven daily 20 miles to work, drives and rides excellent
in the works for spring:
         small block chevy built for 600- 4000 rpm range
         full interior cage
         35 inch ssr's
         detroit for the rear
         4.7;1 gears for t-case
                     
 

[furry fiddler]

 " I FOUND THIS TOPIC POSTED IN JANUARY BY `CRAWLER DAN` AND THOUGHT ITS A REALLY GOOD IDEA"

 For some time its been bugging me why people dont give a write up of their projects,trucks,toys what ever and this would REALLLLY help any up and coming crawlers or truck lovers to find out the simple answers of how their own truck could look,WITH ASKING ON THE FORUM.

from a photo you could get a lot of information, such as :
-how high it sits on a certain lift
-what certain tyres tyres look like (tread paterns) 
-body lifts
-axle widths
-tire hieghts and widths
-exo cage ideas
     " THE LIST IS ENDLESS" BUT SAVES A LOT OF TIME WHEN YOUR LOOKING FOR ANSWERS FOR HOW THINGS `LOOK`........FOR BEGINERS OR EXPERTS FROM ALL COUNTRYS"

ALL YOU NEED IS A COUPLE PHOTOS; 1-FROM THE FRONT, 1-FROM THE SIDE. 1- FROM THE BACK, ON FLAT GROUND, THEN PEOPLE CAN SEE HOW A TRUCK SITS,AND ANY OF YOUR BUILD OR FLEXING IT.

                                                (((((((((   SIMLPE   ))))))))))

 BUT DONT FORGET PHOTO`S. "WHAT DO YOU THINK ?"