Author Topic: The Capacity/Size/Weight/Length Thread (Read 195531 times)

BigMike · « **on:** May 07, 2005, 10:52:43 AM »

This Thread is Featured in our Tech from our Forum Members section!

This is a place to put all common specifications/capacities/sizes/widths/lengths/etc for our beloved Toyota Trucks!!

I'll start it off:

Toyota Front Axle Widths:
55.3" wide, '60-83 FJ40
55.5" wide, 29" spring perch centers, '79-85 Toyota trucks and 4runners
58.5" wide, '81-87 FJ60
58.5" wide, '86-95 IFS front end
63.5" wide, '91-92 FJ80
63.5" wide, '93-97 FZJ80
65" wide, '93-98 T100 IFS front end

Toyota Rear Axle Widths:
55" wide, '79-85 trucks/4runners
55.1" wide, '60-83 FJ40
57.9" wide, '81-87 FJ60
58.5" wide, '86-95 trucks/4runners
60" wide, '95.5-up Tacomas/4runners
62.2" wide, '91-92 FJ80
63" wide, '93-97 FZJ80
66.75" wide, '93-98 T100 trucks

Some Capacities:
##R Engine Oil: 5 Quarts
#VZ Engine Oil: 5.5-5.75 Quarts
3RZ Engine Oil: 5.5 Quarts
4.0 Toy V6: 6.4 Quarts
4.7 Toy V8: 6.0 Quarts
W56: ~3.0 Quarts
Gear Drive T/Case: 1.5 - 1.7 Quarts
Crawl Box: ~0.8 Quarts
Crawl Box + Gear T/Case: 2.3-2.5 Quarts
Toy Hilux Differential Gear Oil: 2.3 Quarts

Drivetrain Lengths:

Marlin Crawler Transmission	Dimension Chart
	by Marlin Czajkowski

Transmission	Length of Bellhousing	Distance to Shift Handle	Distance to T-Case Handle	Total Distance
L45/L50/L52	-	19-1/16"		20-3/4"
G52/G54 (84-87 22R Carb)	6 3/8”	19”	23 ½”	25 ½”
W56 A, B (85-89 22R EFI)	6 3/8”	21 ¼”	--	25 ½”
W56 C, D, E (89-95 22R EFI)	6 3/8”	19 1/8”	24 ¼”	25 ½”
R150 (88-95 3.0 V6)	6 ¼”	21 7/8”	--	24 7/8”
R151 (86-87 22R Turbo)	6 3/8”	19”	23 ½”	25 5/8”
W59 (96-04 22R, 3RZ Tacoma)	6 7/8”	22 ¼”	--	25 ½”
R150 (96-04 3.4 V6)	7 3/8”	23”	--	26 1/8”

Marlin's personal opinion on Transmission Strength Comparison:
G52 is 0% stronger than a L52.
G54 is 20% stronger than a G52.
W56 is 40% stronger than a G54.
R15# is 100% stronger than a W56.

Transfer Case Lengths:
Gear Drive T/case from front face to rear flange face: 14" (apprx)
Gear Drive T/case from front face to front flange face: 1.75" (apprx)
Marlin Crawler Dual Case Unit: 6.5"
Chain Drive T/case from front face to rear flange face: 12.5"
Chain Drive T/case from front face to front flange face: 3.25"

Engine Data:

Engine....	Valves..	Displacement..	Horsepower....	Torque........	Bore......	Stroke....	Compression
18R-GE	2	1968cc	135@5800	127@4400	88.5mm	80	8.3:1
20R	2	2189	90@4800	122@2400	3.48"	3.5	8.4:1
22R	2	2366	96@4800	129@2800	3.62"	3.5	9.0:1
22R-E	2	2366	112@4600	142@3400	92	89	9.0:1
22R-TE	2	2366	135@4800	173@2800	3.62"	3.5"	7.5:1 - Boost: 6 psi

2RZ-FE	4	2.4l	142@5000	160@4000			9.5:1
3RZ-FE	4	2693	150@4800	177@4000	95	95	9.5:1
2TR-FE	4	2693	165@4800	183@4000	95	95	9.5:1 with VVTi (2005+)

3VZ-E	3	2958	150@4800	180@3400	87.5	82	9:1
5VZ-FE	4	3378	190@4800	220@3600	93.5	82	9.6:1

5M-GE	2	2759	161@5600	169@4400	83	85	9.2:1
7M-GE	4	2954	199@6000	188@3600	83	91	9.2:1
7M-GTE	4	2954	232@5600	254@3200	83	91	8.4:1 - Boost: 5 psi

F	2	3878	135@3800	217@2000	89	102	7.5:1
2F	2	4230	140@3600	218@1800	94	102	7.8:1

1GR-FE	4	3956	236@5200	266@3800			10.0:1
2UZ-FE	4	4664	245@5400	315@3400			9.6:1 2000-2004
2UZ-FE	4	4664	271@5400	313@3400			9.6:1 2005+
3UR-FE	4	5663	381@5600	401@3600	94	102	10.2:1

Added 12/31/2012:
Toyota Standard Bolt Torque Specifications as taken from a 1985 FSM
Here is the direct link to the full size image (1581x985 pixels): standard-bolt-torque-specifications.gif
Here is a preview image which links to the full size image:

BigMike · « **Reply #1 on:** May 08, 2005, 08:21:53 PM »

Wheelbases:

1960-83 Landcruiser FJ40: 90"
1963-67 FJ45 Shortbed Pickup: 95.7"
1963-67 FJ45 Longbed Pickup: 104.3"
1968-79 FJ55: 106.3"
1981-87 FJ60: 107.5"
1988-90 FJ62: 107.5"
1991-92 FJ80: 112.2"
1993-97 FZJ80: 112.2"

1979-83 Shortbed: 103"
1979-83 Longbed: 109"

1984-88 4Runner (-1989) & Shortbed Trucks: 103"
1984-88 Xtracab & Longbed Trucks: 112"

1989-95 Shortbed & 4Runners: 103"
1989-95 Xtracab & Longbeds: 122"

2004 Tundra Double Cab: 140.5"

2005 Tacoma Regular Cab: 109.4"
2005 Tacoma Access Cab: 127.2"
2005 Tacoma Double Cab - Short: 127.2"
2005 Tacoma Double Cab - Long: 140.9"

VIN Chassis Identifiers: (added 8/7/2006)

Model	Style	Year	Code	Engine
Hilux 4WD	Std/Long Bed	1980 - 1980	RN37/47	20R
Hilux 4WD	Std Bed	1981 - 1983	RN38	22R
Hilux 4WD	Long Bed	1981 - 1983	RN48	22R
Hilux 4WD	Diesel	1984 - 1984	LN65	2L
Hilux 4WD	Turbo Diesel	1985 - 1987	LN65/66	2LT
Hilux 4WD	Carb	1984 - 1988	RN60-66	22R
Hilux 4WD	EFI Reg & XCab	1985 - 1988	RN60-66	22R-EC
Hilux 4WD	TrboReg & XCab	1986 - 1987	RN61/66	22R-TEC
Hilux 4WD	V6	1988 - 1988	VZN61/6	3VZ-E
Hilux 4WD	I4 RegCab	1989 - 1995	RN101/6	22R-E
Hilux 4WD	I4 X-Cab	1989 - 1995	RN110	22R-E
Hilux 4WD	V6 RegCab	1989 - 1995	VN100/5	3VZ-E
Hilux 4WD	V6 X-Cab	1989 - 1995	VZN110	3VZ-E

4Runner 4WD	I4 Carb	1984 - 1984	RN60	22R
4Runner 4WD	I4 Turbo	1986 - 1987	RN61	22RT-EC
4Runner 4WD	I4 EFI	1985 - 1989	RN60/61	22R-EC
4Runner 4WD	I4 SR5	1990 - 1995	RN130/1	22R-E
4Runner 4WD	I4	1996 - 2000	RZN185	3RZ-FE
4Runner 4WD	V6 SR5	1988 - 1989	VZN61	3VZ-E
4Runner 4WD	V6 SR5	1990 - 1995	VZN13#	3VZ-E
4Runner 4WD	V6	1996 - 2002	VZN185	5VZ-FE
4Runner 4WD	V6 SR5/LTD	2003 - 2007	GRN215	1GR-FE
4Runner 4WD	V8	2003 - 2007	UZN215	2UZ-FE

Tacoma Prerun	I4 XtraCab	1998 - 2004	RZN196	3RZ-FE
Tacoma Prerun	I4 4Dr	2001 - 2004	RZN196	3RZ-FE
Tacoma Prerun	I4 RCab	2005 - 2007	TRN240	2TR-FE
Tacoma Prerun	I4 XCab	2005 - 2007	TRN245	2TR-FE
Tacoma Prerun	V6 XtrCab	1998 - 2004	VZN195	5VZ-FE
Tacoma Prerun	V6 4 Dr	2001 - 2004	VZN195	5VZ-FE
Tacoma Prerun	V6 X-Cab	2005 - 2007	GRN245	1GR-FE
Tacoma Prerun	V6 4Dr Short	2005 - 2007	GRN245	1GR-FE
Tacoma Prerun	V6 4Dr Long	2005 - 2007	GRN250	1GR-FE
Tacoma Srunner	V6 X-Cab	2001 - 2004	VZN195	5VZ-FE
Tacoma Xrunner	V6 X-Cab	2005 - 2007	GRN225	1GR-FE
Tacoma 4WD	I4 RegCab	1995 - 2004	RZN161	3RZ-FE
Tacoma 4WD	I4 XtrCab	1995 - 2004	RZN171	3RZ-FE
Tacoma 4WD	I4 RegCab	2005 - 2007	TRN260	2TR-FE
Tacoma 4WD	I4 X-Cab	2005 - 2007	TRN265	2TR-FE
Tacoma 4WD	V6 RegCab	1995 - 1997	VZN160	5VZ-FE
Tacoma 4WD	V6 XtrCab	1995 - 2004	VZN170	5VZ-FE
Tacoma 4WD	V6 4 Dr	2001 - 2004	VZN170	5VZ-FE
Tacoma 4WD	V6 X-Cab	2005 - 2007	GRN265	1GR-FE

T100 4WD	V6 RegCab 1/2T	1993 - 1994	VCK20	3VZ-E
T100 4WD	V6 RegCab/XCab	1995 - 1998	VCK21	5VZ-FE
Tundra 4WD	V6 RegCab	1999 - 2004	VCK40	5VZ-FE
Tundra 4WD	V6 4 Dr	1999 - 2004	VCK40	5VZ-FE
Tundra 4WD	V8 RegCab	1999 - 2006	UCK40	2UZ-FE
Tundra 4WD	V8 4 Dr	1999 - 2006	UCK40	2UZ-FE
Tundra 4WD	V8 4 Dr	2004 - 2006	UCK41	2UZ-FE

Hyena · « **Reply #2 on:** May 08, 2005, 08:26:21 PM »

What about dual transfer cases? whats the oil specs on those?

BigMike · « **Reply #3 on:** May 08, 2005, 08:33:35 PM »

Quote from: BigMike on May 07, 2005, 10:52:43 AM

Tcase: 1.5 - 1.7 Quarts

Some transmissions have a larger cavity in their tailhousings, so as the transfercase is bolted up behind the trans, a bit more oil is needed to fill the larger cavity.... I believe it's the W's

Hyena · « **Reply #4 on:** May 08, 2005, 09:01:29 PM »

How much more oil is in the back part of the t-case then in the front? Like in the 4wd section rather then the front box part? Or does anyone know?

BigMike · « **Reply #5 on:** May 08, 2005, 09:04:36 PM »

Oh whoops, I think it's 0.8 quarts for a Crawl Box. So about 2.5 for a complete Dual Case.

Hyena · « **Reply #6 on:** May 09, 2005, 05:35:11 PM »

Cool, thanx. You should make this a sticky!

MiniSimp · « **Reply #7 on:** May 09, 2005, 05:55:19 PM »

Quote from: BigMike on May 08, 2005, 08:21:53 PM

Wheelbases:
1984-88 4Runner (-1989) & Shortbed Trucks: 102.95"

Fixed it for ya Mike

Hyena · « **Reply #8 on:** May 09, 2005, 06:09:22 PM »

I think he was just rounding up. Cuzz 22r's take 4.9 quarts of oil, not 5, but i guess it doesn't hurt it.

MiniSimp · « **Reply #9 on:** May 09, 2005, 06:31:57 PM »

1985 Truck(LWB/SWB)/4Runner Chassis Dimensions

BigMike · « **Reply #10 on:** May 09, 2005, 09:31:09 PM »

Great Excellent Pic

Snowtoy · « **Reply #11 on:** May 10, 2005, 01:52:03 PM »

Quote from: BigMike on May 07, 2005, 10:52:43 AM

#VZ Engine Oil: 5 Quarts ?

I find it takes 5.5-5.75 quarts to fill my 3vze.

BigMike · « **Reply #12 on:** May 10, 2005, 08:18:31 PM »

Quote from: Snowtoy on May 10, 2005, 01:52:03 PM

I find it takes 5.5-5.75 quarts to fill my 3vze.

Thanks for the correction. I had a question mark on that one, it was a complete guess. Im sure there is other data that is wrong to, so if you see something else, let me know-

Snowtoy · « **Reply #13 on:** May 11, 2005, 12:31:48 AM »

I am not sure if it is all 3.0's take more. I know mine has always taken more than the book calls for to register on the dip stick on my '90, as well as on my sisters '95. I am curious if others find it takes more oil as well.

guywithuglyyota · « **Reply #14 on:** May 11, 2005, 12:43:54 AM »

That may be becasue the oil filter absorbs about a pint, maybe a tad more.

Hyena · « **Reply #15 on:** May 11, 2005, 07:00:46 PM »

Make this thread a sticky!!

UNBREAKABLE · « **Reply #16 on:** May 11, 2005, 08:22:13 PM »

somebody has a frame machine or has had to do some "adjusting" on one

synwars · « **Reply #17 on:** May 11, 2005, 09:36:45 PM »

Quote from: 4LOWx2 on May 11, 2005, 12:43:54 AM

That may be becasue the oil filter absorbs about a pint, maybe a tad more.

HOLY FRIGGIN' OIL FILTER. That's huge!!! That's like just under the size of filter we use on our huge CAT engines in our transport trucks!!! Or like the high capacity filter that my friend uses for his chev 350. GOSH!

guywithuglyyota · « **Reply #18 on:** May 11, 2005, 11:26:58 PM »

Really? I thought a pint wasnt all that much. 1 pint= 16oz about 1/2 a quart. Hell my filter (amsoil sdf-15) soaks up a quart=2 pints.

MiniSimp · « **Reply #19 on:** May 17, 2005, 03:30:32 PM »

Weight of Round Steel Tubing

Outside Dia. Wall Thickness Weight per Foot
1.25 .049 0.629
1.25 .095 1.172
1.25 .120 1.448
1.5 .049 0.759
1.5 .065 0.996
1.5 .083 1.256
1.5 .095 1.426
1.5 .120 1.769
1.75 .049 0.890
1.75 .065 1.170
1.75 .083 1.478
1.75 .095 1.679
1.75 .120 2.089
2.0 .049 1.021
2.0 .065 1.343
2.0 .083 1.699
2.0 .095 1.933
2.0 .120 2.409

MiniSimp · « **Reply #20 on:** May 17, 2005, 03:31:26 PM »

mr4x42u · « **Reply #21 on:** May 18, 2005, 11:18:00 PM »

Quote from: Hyena on May 09, 2005, 06:09:22 PM

I think he was just rounding up. Cuzz 22r's take 4.9 quarts of oil, not 5, but i guess it doesn't hurt it.

If you use the ford 1515 filter it will hold about an even 5 quarts and has more paper for filtration..

UNBREAKABLE · « **Reply #22 on:** Jun 01, 2005, 06:17:14 AM »

DAMN! 16"X16" 9/16" Tubing weighs 127 LBS a foot!

BigMike · « **Reply #23 on:** Jun 01, 2005, 06:47:43 AM »

Quote from: UNBREAKABLE on Jun 01, 2005, 06:17:14 AM

DAMN! 16"X16" 9/16" Tubing weighs 127 LBS a foot!

awhotrods · « **Reply #24 on:** Jun 01, 2005, 02:15:54 PM »

any specs on spring lengths?

blackdiamond · « **Reply #25 on:** Jun 01, 2005, 03:39:55 PM »

BigMike,

Are you sure on your V8 engine specs?

I have a 2004 Tundra V8 and it is rated at 245 hp and 315 lb-ft (rpm?) and the new 2005 v-tech trucks are something like 282 hp and 325 lb-ft per the dealer spec.

BigMike · « **Reply #26 on:** Jun 02, 2005, 07:44:57 AM »

I got those #s from motortrend I believe.. I'll add the previous year

blackdiamond · « **Reply #27 on:** Jun 02, 2005, 12:16:21 PM »

From Toyota.com

4.0 V6 (2005)
224 HP @ 5200 rpm
282 LB-FT @ 3800 rpm

4.7 V8 (2005)
282 HP @ 5400 rpm
325 LB-FT @ 3400 rpm

And I nearly positive that my 2004 V8 is
240 HP @ 5400 rpm
315 LB-FT @ 3400 rpm

gotrocks · « **Reply #28 on:** Jun 29, 2005, 09:55:13 AM »

wow i just found this thread and its totally helpful. keep the stats coming

MiniSimp · « **Reply #29 on:** Jul 08, 2005, 09:55:40 AM »

Toyota Leaf Springs

Flat length Front Half Rear Half Width SOA / SUA
80-85 Toyota front 45" 22.5" 22.5"    2.36" SOA
80-85 Rancho 3" Toyota front 45.12" 22.56" 22.56"    2.36" SOA
SkyJacker 5" Toyota front 46" 23" 23" 2.36" SOA
80-88 Toy rear 48" 20.5" 27.5" 2.36" SOA
80-88 4" SkyJacker Rear 49" 21" 28" 2.36" SOA
80-88 5" SkyJacker Rear 49.5" 21.25" 28.25" 2.36" SOA
89-95 Toy Rear 51" 21.5" 29.5"    2.36" SOA

Source: DRM

BigMike [OP]

BigMike [OP]

BigMike [OP]

BigMike [OP]

BigMike [OP]

BigMike [OP]

BigMike [OP]

Related Topics