Topic: 1986 basket case runner need some help

[Sbeach92]

hey everyone, im in need of some diagrams if anyone can help. i got myself in a big pile of  s#it helping a buddy with his runner. its has a 22r engine 22re intake manifold, i cant figure out most of the vacum lines, were getting it running and smogged before we sas swap it and trying to have everything done for koh2019 any help is much appriciated. thanks

[helipilot77]

Here is a link to the Factory Service Manual for an 85' 4runner. It should have everything you need in it.

https://www.dropbox.com/s/dyxpr7pqa4et43o/1985%20Toyota%20Pick-up%20and%204runner%20Factory%20Service%20Manual.pdf?dl=0

[OVRAROK]

Here is a link to the Factory Service Manual for an 85' 4runner. It should have everything you need in it.

https://www.dropbox.com/s/dyxpr7pqa4et43o/1985%20Toyota%20Pick-up%20and%204runner%20Factory%20Service%20Manual.pdf?dl=0

Added to bookmarks..thanks nate

[Sbeach92 [OP]]

ok so finally got all the studs, bolts, gaskets, belts and starter, got a lot of the rig together. as i installed the intake i noticed at the rear of the intake sideof the head there is a port in the head, now i did not disassembly this engine so im not sure whats supposed to go there. if its emmisions were going to need it were in ca and he wants the rig street legal. and also any recomendations for power steering pump he isnt going hydro yet and it has a ifs box
 

[Snowtoy]

.........as i installed the intake i noticed at the rear of the intake sideof the head there is a port in the head, now i did not disassembly this engine so im not sure whats supposed to go there. if its emmisions were going to need it were in ca and he wants the rig street legal..............

If the port has two bolt holes above and one below, it is the EGR valve.

[Sbeach92 [OP]]

OK and that is on the intake side correct, i will take a look tonight when i get to his house. he is getting a p/s pump and some other parts right now, i will try and post some pictures when i have questions, it may take a bit for me to figure it out im not tech savy

[Sbeach92 [OP]]

and if anyone knows of problems i may run into it would be appreciated if given a heads up. engine is 22r block, 22re head installed in a 22re truck so wiring and ecm are all in the vehicle already, haven't put battery power to it yet going to check electrical components today make sure we dont burn it to the ground

[Snowtoy]

OK and that is on the intake side correct.......

Yes, at the rear, after the #4 intake.

[Sbeach92 [OP]]

yep thats it, did all the 22re have egr, or am i better taking this thing to a smog guy and paying them to go through it. we are hoping to start it and try and drive it this weekend, once its smogged and he puts about 500-1000 miles on it to and from work were sas,and caging it he just wants it street legal for now

[Snowtoy]

yep thats it, did all the 22re have egr, or am i better taking this thing to a smog guy and paying them to go through it. we are hoping to start it and try and drive it this weekend.............

All of the them, Fed and Cali smog, came with the egr, as well as 22r's, testing it(test causes the engine to stall) is part of the smog test. 

Do you have a factory manual, or are you using Haynes/Chiltons?

[Sbeach92 [OP]]

hayne chilton manual he is looking for a factory one i know damn near nothing about toyota engines, all my rigs get chevy 4.3 or 5.3 swapped

[helipilot77]

and also any recomendations for power steering pump he isnt going hydro yet and it has a ifs box

Keep the IFS steering box in-place. He’ll need it he’s going high steer. If he isnt going high steer slap some sense into him. Push/pull steering is a problem if lifting the suspension.

[Sbeach92 [OP]]

he is going highsteer, just got his axles lastnight from a buddy of mine he got a 14b/d60 for $1800 trussed with 4.56, detroit rear arb front front needs a stub axle,